Jump to content
SAU Community

Recommended Posts

Hey guys my GTR came from japan with a blitz ID Power Meter.This is all good so far but the way it was wired into the car was not to my taste (at least they didnt drill any holes).ok now while i had an alarm fitted i told them to disconnect the ID meter so i can later wire it the way i wanted to, that time has come :D

ok now it has a red wire and an extra red wire spliced into it, one black wire and a white wire which must of been short so it was extended with an orange wire (must of ran out of white)

now im guessing the:

RED- power (but why is it spliced and now there are 2 red wires)???

BLACK- Earth ???

WHITE/ORANGE- I have no idea ???

Does anyone know what/where the WHITE/ORANGE wire goes.

Where should i get power from?

Anyone have a diagram for this that they can post.

I have attached a pic i took of the whole thing (sorry about quality of pic its from a camera phone.post-7189-1150683639.jpg

Thankyou

Thraso

Link to comment
https://www.sau.com.au/forums/topic/122818-blitz-id-power-meter-installation/
Share on other sites

Thanks heaps michael :P

i guess that pic is the back of the standard GTR comp and shows where to connect the white wire ?

I have one red wire but its spliced to make 2? should i get rid of one? (i have attached another pic highlighted)

Where should i get power from ?

Thanks

Thraso :D

post-7189-1150696464.jpg

Thanks heaps michael :P

i guess that pic is the back of the standard GTR comp and shows where to connect the white wire ?

I have one red wire but its spliced to make 2? should i get rid of one? (i have attached another pic highlighted)

Where should i get power from ?

Thanks

Thraso :D

- yeah that correct, thats the stock gtr ecu pin layout.. basicly fine the wirer in the loom which goes to that pinout and connect it to that

-hmm not sure why the red wire is spliced into 2 maybe chop that off. i jsut connected mine to the power wired that goes to my deck

Yeah thats what i was thinking about the red wire just had to be sure.:)Is there a wire there already in that slot for the ecu?

If so do i connect them together into the ecu?

once again thanks alot Michael.

Thraso >_<

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...