Jump to content
SAU Community

Recommended Posts

  • Replies 238
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

guess im in too, havnt been through bells line yet... damn 20 ppl coming! haha thats gna be pretty good if everyone does show up... and it looks like the list isnt updated yet!

as usual some people will pull out in the last minute, however I'm sure many more will come even tho they have not expressed their interest formally in here!

i'm in how about us who want to meet at richmond meet at maccas here's da details

McDonald's Family Restaurants

Cnr March & Eastmarket Sts Richmond NSW 2753

ph: (02) 4588 5145 Take Away Food

Hi people count me in.Went to the famous mountain today awesome road even if i was in a Toyota hiace flat out doing 60KM/h up the mountain.For the people that think its to far you dont what your missing out on.It will be good to meet some of the other members.lol r32 GTR

I dont know if Richmond Maccas is the best place to meet, not a very big car park and not exactly easy to get a large amount of cars out of the carpark and thru the set of lights right next to it

I wouldnt have a clue of a good place, have u got an alternative suggestion?

I guess I'll head up to richmond with mr slim!

where's the meeting spot? i.e after we head off from richmond and get to bathurst where's the next meeting spot? up the mountain? in the town?

last time we lost a few cars in bathurst town due to traffic lights etc and no one knew where to meet up :blink:

I can't wait to go back to yummy noodle box.. yummmmmm!!!




  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...