Jump to content
SAU Community

Recommended Posts

  • Replies 640
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

The R32 broke down after getting some fuel. A phillips head screw driver and an some investigation found out that a hose inside the fuel tank had come off. Car was driven home at about 7pm.

Everyone who is attending this day please download the Supp Regs and Entry Form below, make sure you read them entirely and return your completed entry form as soon as possible.

Right click save target as

Entry Form

http://www.renew.asn.au/download/Eastern%2...rm%20081006.pdf

Supplementary Regulations

http://www.renew.asn.au/download/EC%2006-1...Supp%20Regs.pdf

Note: Grouping of cars to form a "MINI" race any where on the circuit is NOT permitted

So dose this mean that this is just a sprint style day?

this is my frist track day so maybe i dont understand

Thanks Brad

  • 3 weeks later...

Ok people.

We still have a few spots left that we would really like to fill.

Also, those that have paid already, you need to pay the second half now.

$235 is the final cost so for the people that deposited $100 that's $135 left to pay.

That's a pretty easy way to get payment out of the way.

For people still to enter, you can pay in two lots as well but you have less time to do it in. Say one payment this week, next one in two weeks time.

Also could everyone please fill out and fax their entry forms to RENEW as per the above post. You can also check the first post for links to the forms.

Thanks guys.

Just a heads up:

The links to the forms are broken on the first post Adam.

The links should be:

Entry Form: http://www.renew.asn.au/download/ec06_10_08_entryForm.pdf

Sup Regs: http://www.renew.asn.au/download/ec06_10_0...d_supp_regs.pdf

Call me stupid but since i paid SAU for this... does it just mean that i indictae that in the payment section???

Haha the fax number is on the first page about a third of the way down 02 9416 3845

Yeah just put "paid to SAU" on it.




  • Similar Content

  • Latest Posts

    • Omg Brake pedal removal.. FML!!
    • I mean, I can confirm the TPS is at 100%.... I can confirm when we installed the TB and setup the cable that the TB was indeed fully open at max pedal travel.. the same 'curve' (WRT MAP vs MAP) existed with the previous setup/TB/manifold as well... No, we did not do a run with no intake connected. I would love to go back in time to do such a run to rule out the intake. It would have also been good to do a run with the airbox lid off. There's a test there where increased IAT vs more available air could be a positive tradeoff. I remember taking the lid off my R34 Turbo setup back in the day and noticing a monster increase, even if IAT's did go up. Could be similar. Hard to test unless I find a very deserted road. 
    • That's actually encouraging to be honest. my motor was rebuild many years ago but it's probably done less than 30,000kms and fucc all limiter or drift, majority street / drag / roll racing. It'll be fine 💪🏼 I don't even have lines or a can for the cam breathers installed yet, there is zero oil residue or splatter on or around them, it drives beautifully so it seems healthy. Just a ticky lifter, yet they're almost brand new oem genuine Nissan and haven't done many kms at all...
    • Have you confirmed the throttle body goes to WOT (and stays there) during the run?
    • I'm having a problem. I think it was mentioned above somewhere but can't see it.  I'm stuck in the cycle of, sand, filler, low spot again, put filler, sand, low spot again, now i put filler again and a thicker portion which seems to have helped but I got low spots in other areas. In the image. Circled in red thats where the original low spot was and the shape is the same as the red out line. I've more or less fixed that (still low spot up the top but now I have low spots where the green circled part is.  Is likely the issue that I didn't start with a course sand paper? I sanded the filler with 240 to reduce the risk of not going to far but maybe the issue is that I'm only taking off enough material to remove some of the filler but not the high spots. I now started sanding with 120 and I think I'm seeing a difference. I did fix one dent the other 2 are f**ked and seems like I made another low spot which is indicated by the furthest green circle on the left handside. Any thoughts and solutions?   Also second image. All of these rock chips, can they be filled in with primer or do i need to fill them all with filler/putty? So many rock chips on mine lol.
×
×
  • Create New...