Jump to content
SAU Community

Recommended Posts

depends who ya got the kit off

Meaning? Diffrent company's have a diffrent fit or..?

It's a Veiside Copy that I am getting off someone, he orderd it from Sydney but now needs to sell it, arrives in Brisbane on Friday.

Edited by R33MidnightRacer
Link to comment
https://www.sau.com.au/forums/topic/125308-bodykits/#findComment-2314377
Share on other sites

Like he said, it depends on the quality of the kit.

All copies will most likely need some sort of mods to fit. Mine was relatively easy to fit, but its still not perfect close up.

Some kits require you to trim your front bar reinforcement as well. Not sure if the veilside does. Mine didnt.

Link to comment
https://www.sau.com.au/forums/topic/125308-bodykits/#findComment-2314516
Share on other sites

yeah I just spent the weekend with a mate fitting part of my kit to get it ready for weekend, $600 vertex copy for the 32, required a fair bit of chopping and cutting to get the side skirts on and a bit for the front bar as well. Mainly just the intercooler pipping got in the way for the front bar.

now I just need to get the rear bar fitted then I can spray it :)

but the point is, if you are getting a copy of a kit, dont expectit to just bolt straight on with no problems..

and you might find some rust under your old kit.. like I did :D

post-9307-1152466978.jpg

Link to comment
https://www.sau.com.au/forums/topic/125308-bodykits/#findComment-2316669
Share on other sites

yeah I just spent the weekend with a mate fitting part of my kit to get it ready for weekend, $600 vertex copy for the 32, required a fair bit of chopping and cutting to get the side skirts on and a bit for the front bar as well. Mainly just the intercooler pipping got in the way for the front bar.

now I just need to get the rear bar fitted then I can spray it :dry:

but the point is, if you are getting a copy of a kit, dont expectit to just bolt straight on with no problems..

and you might find some rust under your old kit.. like I did ;)

reciprocating saw and die grinder are the best for these copy kits :D

Link to comment
https://www.sau.com.au/forums/topic/125308-bodykits/#findComment-2319354
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...