Jump to content
SAU Community

Recommended Posts

I understand that an R33 turbo highflowed with VG30 rear housing gives alittle bit extra power rating then the standard 450hp. But will an R34 also with a VG30 rear housing produce even more? Or would it bascially be the same as the R33 with the VG30? And roughly how much more power does it give and does it produce any more noticable lag?

Link to comment
https://www.sau.com.au/forums/topic/126945-r34-gcg-highflow/
Share on other sites

LOL, in other words, the only diff between R33/R34 turbos is the rear housings, which are the same for R34/VG30 anyway.

Correct. Most VG turbos were roller and a few of them were ball as some people have claimed. High flowed ones get new bearings anyway. So my guess is no difference after the high flow. Are the oil and water lines the same on the VG as they are on the RB?

Edited by ryan_o_grady
I understand that an R33 turbo highflowed with VG30 rear housing gives alittle bit extra power rating then the standard 450hp. But will an R34 also with a VG30 rear housing produce even more? Or would it bascially be the same as the R33 with the VG30? And roughly how much more power does it give and does it produce any more noticable lag?

VG30 and R34GTT turbine covers are the same

Changing from the R33GTST turbine cover to the VG30 (or R34GTT) turbine cover gave 10 rwkw (265 rwkw to 275 rwkw) on an R33GTST (usual upgrades including Poncams).

Boost build was slightly later, around 300 rpm, noticeable, but not terrible.

:( cheers ;)

Correct. Most VG turbos were roller and a few of them were ball as some people have claimed.
VG30 uses the alloy wheel same as Series 1 R33.

The later models (not z31 vg30 that are more similiar to the VL Turbo T3) run the exact same center as the R32 RB20DET turbo, the center being that the center bearing cartridge, turbine and compressor wheels.

So in other words, the later model vg30det turbo's are an RB20DET turbo with slightly larger compressor and turbine housings.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...