Jump to content
SAU Community

standard bov vented to atmosphere.

Dr Boost

By Dr Boost,
in Engines & Forced Induction

 Share

Recommended Posts

rev210 Grand Master

rev210

Posted
Posted

Drivebai,

I reckon just use the factory BOV and plug the intake pipe recirculation hose and leave it to vent to atmo.

The S-afc has a setting called 'Dec-acel' the manual contains some settings to use for the RB25DET, I don't have it to hand atm. HAve a look in the manual. If this setting is disabled the Throttle % will be 0%.

red17 Experienced

red17

Posted
Posted

46n2,

Yes its normal, the 32's with standard bovs are very loud. Ive now got one that vents to atmosphere and is quieter. Theres nothing wrong with the operation of the standard bov, its just that it vents back right before the air filter and is just as loud, if not louder, than an aftermarket one. Seems to be very sensitive to throttle too, where as aftermarket ones tend only to vent LOUDLY when you WANT it to, not all the time.

I was asked by the cops to change my BOV back to factory when it was already factory. They couldnt believe how loud it was.

Red17

rev210 Grand Master

rev210

Posted
Posted

I put the plumb back hoses on again and tried blocking the hole under the BOV to see what it does in real life.

I actually like the effect it has, except it certainly doesn't make the car quicker (for those who thrive on placebo effects). It does give a better response when the throttle pushes the vacume into a range just before '0'.

Jay95R33 Grand Master

Jay95R33

Posted
Posted
Originally posted by rev210

I put the plumb back hoses on again and tried blocking the hole under the BOV to see what it does in real life.  

I actually like the effect it has, except it certainly doesn't make the car quicker (for those who thrive on placebo effects). It does give a better response when the throttle pushes the vacume into a range just before '0'.

That's pretty much the same result I had. It sort of feels snappier (very technical term !!) around the 0 to on boost part.

But the thing I like the most is it's quieter than before :D I don't get the sound of air recirculating as much now. The HKS filter does enough of that (which I'm thinking of swapping it for the standard box sooner or later)......

J

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...