Jump to content
SAU Community

Recommended Posts

I recently installed a sub in the boot of my r32.. when its on, the bumper resonates alot. anyone know any cheap, effective methods to stop this? thanks!

Remove the sub

Seriously the low frequency noise over time lossens things that are so hard to get too that you will be pulling your car apart to tighten everything up.

autobarn used to sell this spray on tar/ashfault sound deadening shit you spray on the inside of your boot then pave it into shape im not sure if they sell it anymore or who else might have it.

p.s USE IN WELL VENTILATED AREA, (ME AND FRIENDS DID IT IN GARAGE AND WERE TRIPPING FOR HOURS!@! i looked like the guy in my avatar and im white)

With my car, it's the boot lock barrel that rattles in the bootlid. I can get my hand in there and put a finger on it, then the vibration noise stops.

If so, i'm not sure that you could tape it up or anything, it needs to turn. I'm thinking a heavy smearing of thick grease would stop thin bits of metal from hitting each other.

Maybe check that your spoiler isn't the cause too... and lastly... the licence plate usually complains, so back it with rubber then screw it back on.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...