Jump to content
SAU Community

Autometer C2 Tacho

HOT_R33

By HOT_R33,
in Queensland

 Share

Recommended Posts

Col-GTSX Grand Master

Col-GTSX

Posted
Posted

Very construstive advice there Greg, just like the one I just saw in the spotted skyline thread...

Put a resistor in line with the bulb...

Run it in series... About 1 ohm should knock a bit of brightness out of it. Otherwise get a variable pot of lets say 1-5 ohms and then it will be adjustable...

Once again run it in series...

Cost you less than 20 cents for an inline resistor and about $2 for a variable pot...

Cheap as chips...

Munkyb0y Grand Master

Munkyb0y

Posted
Posted

that's like a beacon out in the middle of the sea.

i dont think u needed to point an arrow to it, i reckon we would have found it anyways.

go the resistor. if it's still too bright, add another resistor, or one of higher value.

HOT_R33 Proficient

HOT_R33

Posted
  • Author
Posted
Here you go Sean...

Simple wiring diagram for ya... Just need to wiring it in series and your sorted...

Thanks col, only problem is I've mis-placed my manual for it and all the wires are in those wierd american colours, don't know which wire is the one that connected to the head lights. :(

Oz Grand Master

Oz

Posted
Posted

1.) Check the power to the White (illumination) wire. This is your power input to the light and the amount of power will vary depending on how and where you have it hooked up. The lower the power, the dimmer the light and the higher the power, the brighter the light. A common range is from 6 to 14 volts.

2.) If your tach features LED lighting such as Cobalt, C2, or NV models, and you have confirmed power to the White (illumination) wire, please visit the Ask A Question or Contact Us pages to communicate with our Tech Department.

3.) If your tach uses a replaceable incandescent bulb (check your instructions), inspect the filament of the bulb and replace as necessary. Very few of our tachometers use an incandescent bulb that is not consumer replaceable. If you believe you have one of these units, please visit the Ask A Question or Contact Us pages to inquire about having the bulb replaced.

That Might help...

www.autometer.com

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Looking for someone with a R34 front bar

      By GTSBoy · Posted

      That looks good, but I think you're going to need much beefier side skirts now.
    • GTSBoy
      Most women will agree that parking is the most taxing part of driving

      By GTSBoy · Posted

      They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • GTSBoy
      new 1.5 LSD issues/concerns

      By GTSBoy · Posted

      I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • GTSBoy
      M35 Brake caliper replacement

      By GTSBoy · Posted

      Define "starting to fail". Wy not just rebuild them?
    • GTSBoy
      S1 rb25/s14 starting problem

      By GTSBoy · Posted

      Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...