Jump to content
SAU Community

Recommended Posts

Only few items left:

- R32 standard driver seat $50

- R32 standard fuel regulator $8

- R32 standard pipe from turbo to air filter $8

- R32 standard manifold $10

- R32 standard rear wing with break light $10

- Blitz full auto turbo timer $40

post-30725-1157501543.jpg

post-30725-1163002738.jpg

Edited by cookiebear
Link to comment
https://www.sau.com.au/forums/topic/128014-few-standard-r32-parts-left-cheap/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Need to sell my front mount intercooler now, that fit direct to the standard one and if anyone doesn't want to spend much, that's a very good option. $80 with all the piping and fit straight to any R32, R33, S13 and 180SX etc., you can even fit that in yourself, VERY EASY.

*See the photo on top*

r33boy, I'll find oput the postage and get back to you, but I don't think that'll be much.

NateR31, that's the one still on my car, but I'll get that off next week and replace with a bigger one to match my new turbo.

GTST, what about I pay you the same amount and you get me one with all the pipping posted to SA?

oh ok sorry, you have all the stock piping? as i only have aftermarket piping for my current fmic, but this would be nice as it will still look stock in the bay, if you can find out shipping id be intrested, melb 3195

should be around $30

no need to be snappy.

Why don’t you find out the cost of postage to 4509 then?

You’re the one looking to sell.

I made an offer which was what you wanted for the cooler but for you to pay for the postage of what.. $10 - $20?

Find out what it is to post to 4509 and let me know.

NateR31, GTST, I'll find out the postage for you guys once I got that off my car this week, but I think the postage won't be much, and that's with all the pipping.

*I mean all the pipping is once you take your standard intercooler off, I've all the pipping that goes from there to the front. Photo will be update once that's off my car, thanks.

NateR31, I'll try to get some photos from my car tomorrow and post them up here, may be that's easier for everyone to see. Anyway, didn't you say you have a front mount intercooler already? Why do you have to get another one?

markimak, the S14 Vertex rear bar (new) is still for sale, if your friend is really interest, please let me know soon, because that bar is sitting and selling at my friend's shop, not in my house, thanks.

NateR31, I'll try to get some photos from my car tomorrow and post them up here, may be that's easier for everyone to see. Anyway, didn't you say you have a front mount intercooler already? Why do you have to get another one?

so i can use the stock piping route, im sure it will cater for my needs aswell.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • 440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
    • Appreciate everything guys. I did go ahead and get an alignment... most of my complains are solved. Car is not perfect, but it's good enough. If I notice uneven tire wear or anything I'll just take everything back to stock.  Thanks again!
    • They still have not shipped the 550cc injectors as they weren't in stock, so in theory I could ask to get the 440cc ones instead, if those work better in my scenario. They're the same price so really shouldn't be an issue. Unfortunately I am not so knowledgeable in most parts of tuning so I wasn't sure what's best to choose between the two. 440cc ones are the lowest they have (not in stock, but available to buy nonetheless).
×
×
  • Create New...