Jump to content
SAU Community

Recommended Posts

Hey guys,

Anyone had issues with theitr fuel gauge not working?

Today - Filled up before a dirt track day - I have done around 140kms since filling up and my fuel gauge has not moved from full.

Any tips / tricks to make it work so I dont run out of fuel? :P

Cheers,

Chris

Link to comment
https://www.sau.com.au/forums/topic/129068-fuel-gauge-stopped-working/
Share on other sites

check your level sender in the fuel tank mate. its common for them to fall off their hooks in the 33's.

my car used to show a full tank till i got a half tank then it dropped almost instantly.

just open the fuel tank, re-mount it and it should be right.

Thanks for the tips Joe and Vic!

:)

level sender - when you say open the tank - as in where you put the fuel in - that part?

sorry if it sounds like a silly question!!

hmm...I filled up today already :( so ill wait and see what it does and check out next weekend

thanks guys!

and Vic - which one is the fuse for it???

level sender - when you say open the tank - as in where you put the fuel in - that part?

sorry if it sounds like a silly question!!

oI had this too and it wa the level sender had fallen off.

To answer your question, No. You have to open the tank from the boot. There is an 6-8" hole in the tank in the boot behind the partition, under a metal plate that is screwed down by 4 screws. There is a big cap screwed onto it that has 2 plugs and 3 hoses. You need to remove all the plugs and hoses and open it with a hunk of wood and a rubber mallet. Check out in the DIY section adn look for fuel pump install for instructions on how to open the tank. DON'T FORGET to disconect the battery and remove before doing this...big badda boom.

no worries mate.

im talking about the access through the boot. there is a panel with 4 bolts holding it in, next to your battery in the boot.

i recommend you wait till your tank is almost empty before you do this.

1. take the panel off

2. disconnect the looms (leave the hoses running from the lid because fuel will rush out of it. watch out you dont damage any when loosening the cap).

3. get a plank of wood or a long screw driver and hammer then hold it onto the little little fin things on the cap, then hammer it around to loosen (let me know if this needs to be explained a bit better). watch out for the rubber seal around the lid.

4. detach the fuel lines and remember where each one goes. the reason i left the hoses for this stage is when the fuel starts rushing out you'll be able to let it flow back into the fuel tank.

5. grab the level sender and mount the sucker back on.

6. when putting the lid back on, i recommend using a bit of WD40 to get the lid and the rubber seal sitting snug inside where the cap goes on. you'll know what i mean when you see it.

7. put the rest on in the reverse order and it should be right :thumbsup:

here are pics of what it looks like in the r33's and where it should be inside the tank once mounted:

DSC00406.jpg

DSC00407.jpg

I think the pump is at the back somewhere? not exactly sure

Here is a guide on installing a new fuel pump, might help in opening the fuel tank: http://www.skylinesaustralia.com/forums/in...showtopic=85375

While your at it just upgrade the stock fuel pump :thumbsup:

YOU GUYS RULE!!!!

Guys - thanks heaps for the replies!!!!!

Ill get around to it over next weekend when the fuel levels gone down!

Once again - cheers and I'll have to give you guys virtual beers for your help :no:

Cheers,

Chris

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...