Jump to content
SAU Community

Recommended Posts

hey guys i got a power fc on my r33. i was just wondering if my power fc reads a temp of over 90 after a while of driving should i be worried? the temperatire needle is always on half way so it seems ok there, but just wondering what should the average reading of the water temp on the power fc be.

cheers

Link to comment
https://www.sau.com.au/forums/topic/129938-rb25det-water-temp/
Share on other sites

Hmmm... How high over 90? 99 or 91?

There is a bit difference between the two. :)

If its 90/91 i wouldnt be worried, depends on other factors aswell.

Cruising 100km/h is it the same?

Is it only that temp in peak hour traffic?

Bit more info dude, but it sounds ok at this stage.

don't worry its nothing

my old man's corvette gets up to 110deg in traffic before the fan comes on

remember the water is under pressure so it boils at a much higher temperature than normal water. plus there's the anti-boil added that should assist even further..

The thermostat is 82 deg C??? On the street my handset say about 82-85. So for potting around the thermostat isnt cracking???? Or should i be checking that mine is ajmmed open. Because my temps sit so low on the street, i normally pull the pin at the track when the temp gets to around 90-95 (depends how much lomger the session is and how hot ther dy is etc if i push past 93 etc

82-85 on the street is A-OK Roy. The temp sender may not be accurate to the degree but most engine temps sit at or just above the thermostat temp. On hotter summer days it'll be 5-10C higher than the thermostat temp. Normally a thermostat will close roughly 5C lower than its set temperature.

Also I think high 90s is OK for the track. I'd probably think about pullin the plug when its more like 110C? Remember with a proper cap + coolant it wont boil until 120C.

82-85 on the street is A-OK Roy. The temp sender may not be accurate to the degree but most engine temps sit at or just above the thermostat temp. On hotter summer days it'll be 5-10C higher than the thermostat temp. Normally a thermostat will close roughly 5C lower than its set temperature.

Also I think high 90s is OK for the track. I'd probably think about pullin the plug when its more like 110C? Remember with a proper cap + coolant it wont boil until 120C.

Cool

Roy,

I think the other dude meant to say the 'R34' thermostat begins to open at 82degree's.

The R32/R33 on the other hand begins at 76degree's.

If the thermostat is genuine or not also depicts the cars operating temperature and how quickly the thermostat opens completely. The genuine opens slow and by little amounts until its nice and hot. This results in a slightly warmer running temp with less fluctuations and a considerably quicker warmup.

The aftermarkets (supercrap autostores etc) open wide and really quickly, the aftermarkets also take ages for the car to reach operating temp from a cold start. On my sisters VL it would tend to run hotter under consistent load with the aftermarket but run cooler just pottering around, in the R32 I haven't seen this problem, it simply ran cool all the time; all though I didn't get to 'really' test it out in hot weather. I dropped the genuine thermostat in the VL as it ran much better and wouldn't over heat when giving it a boot full up willunga hill.

Both genuine and aftermarkets are rated to 76.5degree's.

(I sound like a record) I recently said the same in another thread. :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...