Jump to content
SAU Community

Recommended Posts

I just got a 4 channel amplifier (rockford P4004) and a 10" kicker comp vr. i already have everything and start to work it out 2day...but i found there is no space to let my front speaker wire to go into my car from the door..Is any1 willing to teach and show me with photo? or some1 willing to come and help me to fix it? i dont mind to treat for dinner or pay...please...i stay in hobart!

There is a grommet about half way up your door if you look really closely. You can run them through there.

Alternative is to run the wires through the main door plug (which the standard speaker wires go through). You can pull off the caps and use a coat hanger to pull them through.

Search the forums for more results, but here's on.

http://www.skylinesaustralia.com/forums/in...howtopic=123206

There is a grommet about half way up your door if you look really closely. You can run them through there.

Alternative is to run the wires through the main door plug (which the standard speaker wires go through). You can pull off the caps and use a coat hanger to pull them through.

Search the forums for more results, but here's on.

http://www.skylinesaustralia.com/forums/in...howtopic=123206

i had try to pull it through the original socket place...but the socket come wif a male connector and a female connector...i can drill a big hole on the male connector but not female...coz it hide inside the car i got no idea hot to drill it....is there any guide with photo?thankx anyway..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...