Jump to content
SAU Community

Pineapples

The Dan

By The Dan,
in Classifieds

 Share

Recommended Posts

The Dan Grand Master

The Dan

Posted
Posted

I have 10 full sets. $70 each set.

These are all brand new....not second hand. Will post to anywhere in Oz for this price

One set comprises 4 bushes that are two different sizes. These greatly inhance the rear stiffness of the vehicle and in most cases will improve traction and 1/4 mile times by up to 1 second. Great also for drifting as the new stiffer rear end will tend to slide more easily once traction has been broken.

Link to comment
https://www.sau.com.au/forums/topic/130544-pineapples/
Share on other sites
Anquetil Mentor

Anquetil

Posted
Posted
do you have to remove the cradle to fit these or do you just lower it?

Depends on what configuration you go for?

You can slit the bushes and slot them in by loosening the subframe.

Or do it the hard way and drop the hole subframe installing the bushes without sliting them.

Link to comment
https://www.sau.com.au/forums/topic/130544-pineapples/#findComment-2417437
Share on other sites
The Dan Grand Master

The Dan

Posted
  • Author
Posted
do you have to remove the cradle to fit these or do you just lower it?

You can just remove one half at a time....to install literally takes about 10 minutes, so to answer you question, you can just lower it.

wat brand are these? where u located?

They are superpro and I am located in Brisbane's south

Got any pics? Alloy or Polyurethane?

I will get pics tomorrow ( I keep them at work )...and they are Polyurethane

I will try to sort out some installation instructions and post them up

Link to comment
https://www.sau.com.au/forums/topic/130544-pineapples/#findComment-2418857
Share on other sites
  • 3 weeks later...
  • 2 weeks later...
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...