Jump to content
SAU Community

Nos For Na

dcanna

By dcanna,
in Engines & Forced Induction

 Share

Recommended Posts

dcanna Community Regular

dcanna

Posted
Posted

I was considering putting my RB25DE on the bottle for the 1/4 m, jus wondering if anyone has done this b4, i wanted to kno what else goes along with it ie do i need a/m fuel pumps or a/m ecu that will advance timing? also costs involved and maybe if anyone knows who would install it?

cheers

Link to comment
https://www.sau.com.au/forums/topic/131710-nos-for-na/
Share on other sites
NA_R33 Grand Master

NA_R33

Posted
Posted

dcanna PM replyed.

Hey guys, i used to run a zex wet kit on my 25, with a 75hp shot of giggle gas. Engine handled without a problem. Went from a 15.8 down to a flat 14. Just make sure ur clutch is up to the task and go for gold. I ran the gas on the car for probably 18 months. the last couple of months before doing the engine conversion i intentially tried killing the engine at every chance i got but couldnt. They are very tuff little succers. and it still ran as good as the day i bought the car 5 years ago. Just dont forget to retard the timing a couple of degrees when its on the bottle and you'll be fine.

Link to comment
https://www.sau.com.au/forums/topic/131710-nos-for-na/#findComment-2444543
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Predator1
      Tomei gasket

      By Predator1 · Posted

      Didnt realise RB's had more then 1 head.
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • Kinkstaah
      Unpeeling the Orange

      By Kinkstaah · Posted

      The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
×
×
  • Create New...