Jump to content
SAU Community

Recommended Posts

post-29722-1156629994.jpg

SOLD

FOR SALE IS THIS IMMACULATE TWIN HIGH MOUNT BOLT ON KIT FOR A SKYLINE R32 OR R33, COMES COMPLETE WITH

*TWO KKK K26 TURBOS IN IMMACULATE CONDITION WITH NO SHAFT PLAY AT ALL,

*TWO BIG EXTERNAL WASTEGATES WITH SCREAMER PIPES,

*BLITZ MANIFOLD IN TOP CONDITION (PERFECT WELDS NO CRACKS),

*ALL GASKETS REQUIRED FOR INSTALL ARE INCLUDED,

*ALSO INCLUDED IS TWO K&N POD FILTERS WITH PIPES ALREADY PROFESSIONALLY ATTACHED TO TURBO HOUSINGS,

*2 PIECE DUMP PIPE FROM TURBOS TO CAT INCLUDED ALSO

HAS MADE OVER 400KW AT ALL FOUR WHEELS ON ONLY 22PSI WITH MINIMAL MODIFICATIONS IN AN R32

DONE ABOUT 5000KMS SINCE NEW. IN IMMACULATE CONDITION

REASON FOR SALE IS I AM STRIPPING DOWN CAR AND GOING FOR A FULL DRAG SETUP

ITEM IS LOCATED IN SYDNEY AND PICKUP IS PREFERRED HOWEVER, IF REQUIRED. WILL POST AT BUYERS EXPENSE

PM ME OR EMAIL AT [email protected]

Link to comment
https://www.sau.com.au/forums/topic/131860-sold/
Share on other sites

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

what turbos are they

when was she on ful boost

and dyno graph please

THEY ARE KKR TURBOS K6 SERIES(THEY HAVE A PLAQUE ON THE FRONT OF THE HOUSING I WILL CHECK TO SEE WHAT SERIES FOR SURE)

NO DYNO SHEET AVAILABLE BUT BY MEMORY FULL BOOST BY 4250RPM.

Link to comment
https://www.sau.com.au/forums/topic/131860-sold/#findComment-2441887
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hell, I'm sufficiently wary of the ZSS suspension arms, let alone something like a hub.
    • Got it back home and got started pulling the hub off and diagnose the issue. Axle was stuck after removing the 36mm nut so i used a 3 jaw puller to try and push it out and... eH5FXvJ8.mp4   spend the next few hours trying to remove the axle from the remaining hub as it was very much jammed in there when the spindle sheared off. resulting damage as below R53AIy6 - Imgur.mp4   Looks like the was already a stress fracturing in the spindle as can be seen with the darker cracked section My working theory is maybe when the pinion gear exploded last year the shock put through the hub was the initial crack. Then a few events later it finally let go. Just lucky it happened where it did and not 190km/h on the next sweeper or into the hairpin The bearing/hub assembly went in in 2019 and were non-genuine "ZSS" assemblies and no nails were harmed in the process. #BreakHubsNotNails
    • Thanks mate, couldn't find in VIC, ended up ordering one from NSW, getting rwc to get new plates and registration done.
    • Before all the EFR fan boys come in, have a look at: https://www.garrettmotion.com/racing-and-performance/performance-catalog/turbo/g-series-ii-g30-825-58mm/ It also comes in a T4 1.06 divided housing. I would dare say if you want response & also decent power, this thing would chop.   AND apologies, just re-read your post, you've already bought the turbo... whatever you do, make sure you stick with divided housing and proper twin scroll manifold.
    • People have got to stop doing that. ShatGPT is not a search engine. It is a hallucination factory.   I also would recommend the 1.05. The .83 will "work" for you , in that it will be more responsive, but I think you'll find that it won't be anywhere near as good running it out to 8000rpm as the big housing will be.
×
×
  • Create New...