Jump to content
SAU Community

Recommended Posts

For sale:

R31 Skyline parts

1. Have all 4 doors

2 Back seat

3 Blue Carpet

4 Series 3 taillights - one slightly damaged

5 door rubbers - For around the door frame on the inside of the car rubber and blue clip strip

6 5 speed manual gearbox crossmember

7 boot rubber

8 Bonnet

9 Tow bar and ball

10 Dash surrond - with electrical bits and buttons - small hole modified for a gauge

11 front bumper

12 - BOTH FRONT AND REAR COMPLETE STRUTS , LEFT AND RIGHT ALL 4 !!

King springs all round - lowered 2 inches

- KYB shock inserts - with damper reset for lowered car 2 inches

- With front wheel hubs

- Have receipts for suspension totally over $600

13 carpeted parcel shelf

14 Turbosmart Type II Vee Port Blow off valve - Near new little use..

Condition:

Good condition

No rust

Price and price conditions:

1 $30 ono each , 2 for $50 or all 4 for $80

2 $90 ono

3 $40ono

4 $80 pair

5 $20

6 $70ono

7 $10

8 $30

9 $70ono

10 $30

11 $50

12 $350ono

13 $20ono

14. $155ono

Extra Info:

any other details you wish to mention.

Contact Details:

State how you would like to be contacted. If you don't get on the site much, leave other contact details such as email or phone numbers.

Location:

Im Near Penrith, Sydney

Delivery & Conditions of Delivery:

Pick up prefered but can post some stuff at buyers expense

e5_1.JPG

54_1.JPG

3d_1.JPG

84_1.JPG

33_1.JPG

59_1.JPG

ea_1.JPG

17_1.JPG

4b_1.JPG

e3_1.JPG

:sorcerer: :sorcerer: :ninja:

Link to comment
https://www.sau.com.au/forums/topic/132075-r31-skyline-parts-turbosmart-bov/
Share on other sites

  • 9 months later...
  • 4 months later...
  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...