Jump to content
SAU Community

Recommended Posts

Hey guys im bout to rebuild my engine and i was wondering who you all think is the best company/person in vic is to do it. Im in the south east subs. But for quality i will travel out. Price is important but quality is wat im really looking for. Any help would be great thanks.

Link to comment
https://www.sau.com.au/forums/topic/132604-engine-builders/
Share on other sites

depends on the money you want to spend really... places like ICE performace are good but they are starting to get expensive, Hypertech aswell... MSC is a good bet too

MSC Performance & Dyno Tuning

9469 5282, 43 Radford RD Reservoir

Race Pace is very good also, GTR's are the speciality there but call up and ask some questions, im sure they can help too

Link to comment
https://www.sau.com.au/forums/topic/132604-engine-builders/#findComment-2457369
Share on other sites

Ivan grow up you moron

vsute - checkout this link which is in the sticky thread here in this section :)

http://www.skylinesaustralia.com/forums/in...c=13305&hl=

My pick, Racepace. No-one else in Vic has the knowledge/quality of Ben and the crew.

Thats assuming you are talking about RB motors :)

Link to comment
https://www.sau.com.au/forums/topic/132604-engine-builders/#findComment-2457496
Share on other sites

i have a quote from guys in tas to build one for 3k with forgies, so i will have to see wat quotes here a like i have sent a few emails way for rough quotes so i will wait and see.

Wat do u think it is going to cost for a rb20 with forgies and some other parts like good bearings, seals/gaskits, rings , maybe rods. Guess it all depends on pro advice on how far to go.

Link to comment
https://www.sau.com.au/forums/topic/132604-engine-builders/#findComment-2457738
Share on other sites

Just remember this little piece of advice when trying to save "a couple of bucks" building a motor

fast + cheap = not good

good + cheap = not fast

good + fast = not cheap

My pick would be P+P Performance in Wagga Wagga. No one in Victoria compares to them, has won as many accolades around the country or has built motors anything like they do.

Edited by frx026
Link to comment
https://www.sau.com.au/forums/topic/132604-engine-builders/#findComment-2457924
Share on other sites

building an engine isnt cheap mate, my brothers sr20 set him back heaps, just pistons rings bearing and rods cost around 3,500 - 4000 then machining cost 3000 (including headwork and stuff)

Link to comment
https://www.sau.com.au/forums/topic/132604-engine-builders/#findComment-2458143
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...