Jump to content
SAU Community

Rip Steve

R334door

By R334door,
in Four Door Family & Wagoneers

 Share

Recommended Posts

FLYSLY Mentor

FLYSLY

Posted
Posted

Im sure most of you are aware by now that our beloved crockadile hunter Steve Irwin died today in a freak accident today, whilst he was filming an underwater documentary he whipped by the tail of a sting ray the bar bell pierced his lung.

You have brought us all laughter happiness and you have done a lot for the australian wildlife and forestry.

And who can forget the great word that we will all remember steve by 'Crikey"

Rest In Peace

And all our thoughts and condolences go out to your family and friends

Link to comment
https://www.sau.com.au/forums/topic/132926-rip-steve/#findComment-2462050
Share on other sites
bazr33 Mentor

bazr33

Posted
Posted (edited)

Yeah steve irwin was one of the aussie blokes i liked to watch on tv

bit shocked to hear on the radio today,

Would of thought that he would of passed away by the help of a croc, rather then a stingray. Not kool anyway .

Feel sorry for the rest of the family and all aussies as we have lost a great icon for australia.

And hopefully the family and ppl at australia zoo, will keep going with what he has started.

CRRRIIKKKEEYYY!!!

Edited by bazr33
Link to comment
https://www.sau.com.au/forums/topic/132926-rip-steve/#findComment-2462158
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...