Jump to content
SAU Community

Recommended Posts

Arias Pistons 5 perfect one damaged

6 week wait from states for new one around $300

set of 5 a 1 bung one $750 0.5 over bore suit rb26 only

Aftermarket R32GTR only GAB shocks and springs semi low set 4 very good cond $450

like new harmonic balancer suit rb20 only new $300 sell $100

m in south australia near Tea tree plaza

please call 0415 344 630

post-31348-1158033569.jpg

post-31348-1158034834.jpg

post-31348-1158034991.jpg

Edited by SIR032GTR
Link to comment
https://www.sau.com.au/forums/topic/133974-assorted-skyline-parts/
Share on other sites

3 ribs on all why would you ask if they are four ribs?

did nissan ever make a 4 rib? thats a pretty wide power steering belt ?

as far as kms who knows the condition is very good though and suits only rb20 det engines possibly non turbo also unsure

as far as indicators they look to be sold

ill confirm soon

Cheers Everyone

3 ribs on all why would you ask if they are four ribs?

did nissan ever make a 4 rib? thats a pretty wide power steering belt ?

as far as kms who knows the condition is very good though and suits only rb20 det engines possibly non turbo also unsure

as far as indicators they look to be sold

ill confirm soon

Cheers Everyone

Most r32gtst power steer pulleys are 4 rib for the hicas pump.

I think i see the confusion

The belt has four ribs and the pulley will suit so it has three ribs as such to match the four ribbed belt

it does fit a rb20det and had the same for alternator and air con etc

hope this clarifys

unknown kms in very good condition

centre bore clean and no cracks

When the guys put my car back together within half an hour a part of the valve guides

broke fell in and crushed between piston and head all fixed now but needed one piston only so

ended ordering 6 to save on time which did not in the end but now i have 5 spare dooh!!!

some one will need them and can order one to mate up a set from USA takes 4 weeks and

around $250 so full set of forgies will cost you $1000 instead of $1399

post-31348-1158577354.jpg

Edited by SIR032GTR
  • 2 weeks later...
  • 1 month later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...