Jump to content
SAU Community

A Few Question For R34gtt Key And Remote

bobby09

By bobby09,
in R Series (R30, R31, R32, R33, R34)

 Share

Recommended Posts

bobby09 Enthusiast

bobby09

Posted
Posted (edited)

Hi I just got R34 Gtt.The key of the car come with remote built in.I just wonder, Is this car has factory immobiliser and if it has ,Where can I get the key with remote and anyone know How to pro gram key and remote ?Thanks a lot

Edited by bobby09
JUNR34 Community Regular

JUNR34

Posted
Posted (edited)

Are you after another original key with the inbuilt remote for the factory immob? Firstly don't bother cause they cost too much because you would need to get one from Japan. Do you have an alarm installed on the car (if not it wouldnt be such a bad idea haha)? If so then you can just make a spare key (cost like $7) at any good key cutting shops, DONT go to the ones in the middle of the mall.

Congrad on your buy, any pics ?

Edited by JUNR34
lanky71 Veteran

lanky71

Posted
Posted

My R34 GT-T comes with central locking but no immobiliser and I got the dealer to put a Australian Approved one on and now I can still use the original central locking buttons but they do not arm/disarm the immobiliser I have a little button on a seperate bit for that....

I am however looking for a Remote Start with SMS Alert alarm/imobiliser if anyone has any good brands or places to get one let me know.

Drew.

wrxhoon Grand Master

wrxhoon

Posted
Posted
How can I know that my car come with immobiliser.And do you know how much for original key thanks

R34 GTR key blanks ( with a chip that activates the factory immobiliser) are about $95 . You have to take it to a locksmith /keycutter with your other key to cut it. Back to the Nissan dealer to program it, cost about $50-60.

If you put a pic of your key on here i can tell you if you have a chip in it, the other way you can tell is cut another key and try to start it if it starts you dont have the chip in it .

Howie Grand Master

Howie

Posted
Posted (edited)

The R34's normally come with an immobiliser that's resistance driven. I.e. if you have a new key cut by your locksmith and it fits into the ignition barrel, just by having the key there it will disable the immobiliser. So therefore you don't necessarily need the remote central locking part coded if you don't want. Those of you who are wondering if you have a resistance driven immobiliser need only look at your working key, and see if there are two small scratch marks towards the end that you hold your key with.

Therefore if you try to hook up a remote start system with a third party alarm, you'll need a kit that will bypass the factory immobiliser. GKTech do one with the viper alarms (option).

If you have any questions about bypassing the factory immobiliser check out my thread i posted under security forum. And the man on sau to speak to is installer Chris Rodgers ... he knows everything you'd want to know about the r34 immobiliser.

Edited by Howie

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Rear subframe stay bracket bolt removal issues

      By GTSBoy · Posted

      Yes. Probably, given that there is only access from the bottom end of it, go with a drill bit. Don't start too small. 7 or 8mm is probably the right size. You want something that can make a big enough hole to do some damage, but not so bit that it clashes with the steel or binds up and breaks your wrist. A slow speed is probably a good idea too. Once the rubber is destroyed, you then have to get the crush tube off the stud, which will be the whole heat/oil/cutting exercise all over again, but this time with the need to strictly avoid damaging the stud (any further than the corrosion might already have done.
    • r32-25t
      R32 Gtr Long Term Love, Now Project

      By r32-25t · Posted

      We replaced the connector just because we could and it was still there, once we swapped the injectors around it stopped. The injectors were something I had thoughts of replacing even before I first started the engine and in hindsight I should have 
    • TheBushKangaroo
      Hello fellow enthusiasts

      By TheBushKangaroo · Posted

      Not too sure just yet, want to have a go at doing what I can myself, but to start with want someone to cast their eye over it tell me what needs doing to get it running and back on the road, so anyone with great overall knowledge would be ideal.
    • MBS206
      Rear subframe stay bracket bolt removal issues

      By MBS206 · Posted

      I personally would go with cutting out the rubber. Then deal with getting sleeve off separately. Rubber can be painful to cut, it loves to jam up cutting tools. I normally have success with drill bits, deburr bits, angle grinders, jigsaw, reciprocating saw, and never forget... fire. Obviously different tools won't work in all locations you're trying to work with, and you need to be comfortable with each. You personally may be happy slowly slicing it out with a razor blade, if you are, go for it with one too! Feel free to wait for others to weigh in also on their thoughts.
    • DatsunBanana
      Rear subframe stay bracket bolt removal issues

      By DatsunBanana · Posted

      So ... I got everything disconnected and started dropping the frame. Three of the four mounts started to come down but the fourth one (the one with the nut that gave me all the trouble) won't budge. The inner metal sleeve stays up tight against the chassis rail although the outer part of the mount drops a bit (and can be levered quite a lot more) but it's just stretching the rubber bushing. So I reckon there's some serious corrosion inside the inner sleeve and holding it tight to the lug at the top of the bolt. Tried everything I can think of so far: penetrating oil, whacking the top of the sleeve to vibrate it and wedge a screwdriver blade in there. I also tried to turn the inner sleeve a bit by hitting it with a chisel at the bottom. It's stuck solid. What do you think about cutting the rubber with a blade so I can drop the subframe around it anyway. Then worry about getting the inner sleeve off after? Will that work? Is it gonna give me even more problems?
×
×
  • Create New...