Jump to content
SAU Community

Recommended Posts

hey people, just took off my apexi pod kit of the 32gtr, looking to jus get a hi flow panel filter.. however i came across a blitz induction cover + blitz SUSPOWER filter.

heres the link:

http://www.perfectrun.com.au/real_size_ima...uctioncover.htm

any comments/experiences?.. design seems similar to an ARC box (for 1/4 the price as well), but for only 1 entry near the cold air feed for the gtr i guess?

ive always looked at pod air fitlers needing a heat shield with CAI route. but for the ARC box & this blitz induction kit, wouldnt the panel filter be just like an unshielded pod filter sucking in engine heat?.

thanks

Link to comment
https://www.sau.com.au/forums/topic/135731-blitz-panel-filter-induction-cover/
Share on other sites

yeah, with the cover you pretty much end up with the same thing as the ARC airbox, only it's not as shiny, and no where near as heavy. Plus the ARC box does have a little tiny filter on the front of the box which your set-up wont have. I had an ARC box on my GTR for a little while and not a huge fan. mainly because it's bloody heavy, and the replacement filters are crazy expensive and it's still just sucking in hot air from your engine bay, but on top of that the whole thing acts like a heatsink and absorbs heat from the engine bay. for now i'm just using apexi pods and will one day get a nice shield made for them.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...