Jump to content
SAU Community

Recommended Posts

Item: HKS 2535 Turbo + all oil lines etc to bolt up

Location: Sydney

Item Condition: Second hand

Reason for Selling: Rebuild and upgrade

Price and Payment Conditions: $1400 ono

Contact Details: PM or post

Selling as i blew my engine and am going to do a slight turbo upgrade as well :) . Turbo has been on car for the last 4 years and has never run over 1.2 bar. Only ran 0.5 - 1 bar on the street with the occassional 1.2 bar at the drags. So has VERY rarely seen even 1.2 bar. :laugh:

Made 249rwkw at hitmans with supporting engine mods, and was tuned down to make a safe 235rwkw at UAS. Can supply dyno graphs if required. :w00t:

If anyone wants to check it out feel free to organise to see it. My mechanic looked at it and said it is in good condition. Pics to follow :sorcerer:

Details on turbo can be found here :

http://www.hksusa.com/products/?id=705

turbo003.JPG

turbo001.JPG

turbo006.JPG

turbo018.JPG

Link to comment
https://www.sau.com.au/forums/topic/136001-hks-2535-direct-bolt-on-for-rb25det/
Share on other sites

pffft its a fake :laugh:

hahaha only joking mona....

I have driven the car on many occasions before the engine blew and I have to say this is one AWESOME turbo for an RB25 and with the hassle free bolt on nature of it, its a good buy :)

Im after a tad more power :w00t: which is why I havent bought this turbo already.

New owner wont be dissappointed....

Hi All!

Also wanted to point out the times I was doing at WSID with the above turbo and supporting mods.

Best time I managed was 12.504 on street tyres, and with the two runs I got with semis i managed to get her down to 12.4. I sure with more runs, this time could have been further lowered! Note: all runs were only ever done with a max boost of 1.2bar.

So as you can see, an awesome power mod all round! ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...