Jump to content
SAU Community

Recommended Posts

Guest | hype^ |

ah nice!!! :uh-huh:

now all i have to fugure out is where the **** i can get a hold of two of em,,

and another Q..

i have no idea about harnesses..

so is there any way of mounting them so the they dont go straight across the back seat..

any way of attaching them to the bottom of the seat?

Link to comment
https://www.sau.com.au/forums/topic/1380-red-type-r-in-r33/#findComment-27556
Share on other sites

Originally posted by | hype^ |

ah nice!!! :uh-huh:

now all i have to fugure out is where the **** i can get a hold of two of em,,  

and another Q..  

i have no idea about harnesses..  

so is there any way of mounting them so the they dont go straight across the back seat..  

any way of attaching them to the bottom of the seat?

To be properly installed you'll have to loose the back seats. Harnesses are illegal anyway and any cop would be able to spot them easily so I wouldn't put them in if it's a street car.

Link to comment
https://www.sau.com.au/forums/topic/1380-red-type-r-in-r33/#findComment-27565
Share on other sites

i remember a while ago that they are very hard to find and are very expensive. I thought someone said that as a honda part (just through a dealership) that they wanted over $4000 for a set?!?

best bet would be to contact one of the jap parts companies, or someone on this forum like nengun to source you some direct from a wrecked integra in japan.

Link to comment
https://www.sau.com.au/forums/topic/1380-red-type-r-in-r33/#findComment-27675
Share on other sites

Originally posted by Merli

They are $3500 *EACH* new from Honda...

Andrew. :uh-huh:

thats what i thought.. but didnt want to say *each* in case of making myself look like a damn fool - (like someone that would actually pay that much for them!)

so, as i said, sourcing them from japan would be the cheapest i guess.

also, are these 'red' seats the same as the black ones. We had a 99 integra type r and it had black recaros

Link to comment
https://www.sau.com.au/forums/topic/1380-red-type-r-in-r33/#findComment-27730
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...