Jump to content
SAU Community

Recommended Posts

Anybody done this back to back testing.

E.g. Shell 98 AFR 12:1, then run shell extreme (E5) and checked how much the AFR had moved?

Anybody done this with E10?

Is the AFR change enough to warrant a retune? Or most of the time ok if tune was to 11.8:1 AFR with optimax?

Thanks

Edited by benl1981

And from this did he deduct that a leaner mixture increased EGT when run on the same tune? There is three things your have to wieght up 1. is the less density of the Ethanol 2. the fact that alcohols generally produce lower EGT's. 3. How much oxygen the ethanol is carrying.

From my experience with a wideband, the AFRs moved about ~0.3-0.4 leaner using E10. E5 would be half of this.

Thanks Busy2k - thats the kind of info I was chasing.

So its not that significant.

i.e. If the tune is safe with normal 98 (i.e. 11.8:1) then it should still be safe running boost98 (E10) it sounds like. I think the ethanol lowers the EGTs slightly anyway?

Since you have to up the timing anyway - I presume by using the ignition correction on the pfc - then can't you increase the injectors by some amount - also in the correction bit - to lower the AFR and thus make the tune happy again?

You would have to remember to do it every time you turned the car on though.

Yep by putting in the E10 it should be still quite safe. But to get the most out of it, you may have to up the ignition timing 1 or 2 degrees. Changing the fuel injector correction (ie from 50 to 51% if using 740cc injectors) should be enough to offset the changes in AFR. A dodgy way to permanantly increase the ignition timing is to advance the CAS 1 or 2 degrees if you have a timing gun.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...