Jump to content
SAU Community

Recommended Posts

falken zeix 255/40/r17 x 2 these havnt been driven on still got lil bits that stick up retail for $280 each lookin for $450 for the pair.. people who have used them rate highly !! reason for selling realised there too wide to fit on the rims i have the shop wouldnt do it

post-30861-1161242864.jpg post-30861-1161242879.jpg post-30861-1161242894.jpg

dunlop p3000 235/45/r17 x 2 worn down couple of mm before markers could be used on street not recomended though lookin for $80 for the pair

post-30861-1161242911.jpg post-30861-1161242922.jpg post-30861-1161242934.jpg

standard cefiro suspension with lowered springs good condition took out due to coilovers lookin for $100 for the lot

post-30861-1161242948.jpg

standard cefiro front bar look at photo for condition lookin for $100

post-30861-1161242968.jpg

nissan gazelle RARE COUPE whole car body damage engine is good condition ca20e was replaced not long ago.. was the project car but dont have the time.. pick up only as is lookin at $700 ono

post-30861-1161243029.jpg

pick up only on everything dont really want to stuff around with postage n that

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...