Jump to content
SAU Community

Rb25det Cheap

Darkon
 Share

Recommended Posts

Darkon Experienced

Darkon

Posted
Posted (edited)

Hey,

I've got a rb25det for sale (bare) motor has blown big end bearing needs a rebuild, has been a really great motor before this was making 209rwkw at 9psi on the standard turbo before it let go

$800 but make me offer must sell

I'm in canberra feel free to contact me by pm or on my mobile 0415 043 496

Thanks

-Shawn

Edited by Slither
Link to comment
https://www.sau.com.au/forums/topic/139656-rb25det-cheap/
Share on other sites
Darkon Experienced

Darkon

Posted
  • Author
Posted

as far as we can tell nothing, it was recently compresion tested cos it dropped to five cylinders, and all cylinders where good (turned out to be a ecu fualt) then a little while later it just devolped a knock that has been put down to a big end, it has about 130,000 on it, but was blowing no smoke or anything and has always pulled pretty remarkable results with minor mods actually really disappointed to see it go but i got another motor to put in and need to sell this one to pay for it, the motor can still be started now and will run fine but we've avoided doing this naturally to avoid the chance of doing any damage

Link to comment
https://www.sau.com.au/forums/topic/139656-rb25det-cheap/#findComment-2611087
Share on other sites
Darkon Experienced

Darkon

Posted
  • Author
Posted
ummmm you sure?

hell yeah it was a bit of a shock first dyno run of the bat with the new ecu pulled 210 hang on did i say 209 meant 211 and yeah just tweaked it till 211 thats was with standard pump injectors and turbo, but blitz neuro spec V exhaust decatted splitfire coils and blitz cooler with link ecu running 9psi, it's always been damn quick for what it was

Link to comment
https://www.sau.com.au/forums/topic/139656-rb25det-cheap/#findComment-2611728
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...