Jump to content
SAU Community

Recommended Posts

I have been doing a bit of reading on here to find out what the next mod i should do to my car is.

My goal is about 330rwhp with a good dose of torque

i currently have a S1 33 gtst with:

Turbo back Exhaust

Cold air box w/pod

Front mount cooler

Power FC

Walbro fuel pump

running 13psi

also with a brass clutch

I've read that alot of people have had good success with GCG high flow turbos with a fair wack power atw, but still running standard injectors. I was under the impression you can get a good 295ishrwhp with standards but anything more than that they will start maxing out.

Ive had a maximum inj duty of 97% and its only been tuned to the 270rwhp mark, could that have been a once off spike?

The last thing i want to do is have my engine go bang so i would like your advise on what my next investment should be, or if im missing anything like upgrading my coils etc.

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/140245-what-mod-next-inj-max-out/
Share on other sites

definately do injectors next, 97% is too high, you would also be better off getting a Z32 AFM, cos your factory AFM is near its limits too.

I would recommend doing a fuel pressure reg at the same time, as aftermarket injectors are designed to run at different fuel pressure to the factory.

Factory base fuel pressure at idle is 2.55kg, aftermarket, usually 3.0kg

Having the correct base pressure will ensure that you are getting a nice spray pattern at idle, and also it will mean when you put in for example 550cc injectors, you actually have 550cc injectors, rather than 510cc

I am sure several people will now completely disagree with me :P

definately do injectors next, 97% is too high, you would also be better off getting a Z32 AFM, cos your factory AFM is near its limits too.

I would recommend doing a fuel pressure reg at the same time, as aftermarket injectors are designed to run at different fuel pressure to the factory.

Factory base fuel pressure at idle is 2.55kg, aftermarket, usually 3.0kg

Having the correct base pressure will ensure that you are getting a nice spray pattern at idle, and also it will mean when you put in for example 550cc injectors, you actually have 550cc injectors, rather than 510cc

I am sure several people will now completely disagree with me :D

OK, he says puting his hand up, that would be me.

Aftermarket injectors (eg; Nismo) designed for use with RB25’s use the standard Nissan fuel pressure, which is 34-36 psi (2.3 to 2.5 bar). Aftermarket injectors designed for use on other engines (that may or may not require adaptors to fit RB25’s) may or may not be specified for the same fuel pressure. Their operating and flow rating are specified. BUT (there is always a but) I have not found any injectors that use different fuel pressures that will fit RB25’s.

So while you are right in theory, in the real world that is simply not the case.

Plus I defy anyone to tell the difference in spray patterns between 2.5 and 3 bar base pressure. Remember injectors in turbo engines have to have good spray patterns at absolute pressures ranging from 2.0 to 6.0 bar (plus or minus vacuum and boost). So 0.5 bar is neither here nor there as far as their spray pattern is concerned. This is not always the case in injectors intended for N/A use however. Rochesters for example, like to have their specified fuel pressure at all times and don’t handle drastic increases or decreases.

Back to the original question. With a perfect tune and an engine in perfect condition the standard injectors are OK for around 225’ish rwkw (300 rwhp). But I have only seen that once in over 50 R33GTST’s. The rest have dropped off from 205 rwkw (275 rwhp) onwards, with around 215 rwkw (290 rwhp) being the most common.

An adjustable FPR (eg; Nismo bolt style $150 from Nengun) will facilitate an increase in fuel pressure. It isn’t linear though, a 10% increase in pressure doesn’t equal a 10% increase in flow. For example increasing the base pressure to say 46 psi (30%) enables the standard injectors to stretch to around 400 cc’s (up from 370 cc which is 8%). That’s enough for 235 rwkw (320 rwhp) which his about as far as I would recommend going. The fuel pressure gets too high for the standard size hoses and clamps and fuel fires are very nasty. Hence why I suggest replacing the 10 + year old fuel hoses with new ones. Plus Walbro pumps are not very good at handling pressure, their flow drops off rather dramatically.

A spot 97% injector duty reading is not a very good indication, it may well have been 85% duty, plus 12% for acceleration enrichment. Try looking at the injector duty as you run up through the rpm range at WOT in 3rd and 4th gear (a passenger is handy for that). That is a far better indicator.

The GCG high flow is good for around 265 rwkw (355 rwhp). So if you want to use the full potential of the turbo upgrade you really need to be looking at aftermarket injectors.

Hope that was of some help

:P cheers :D

PS; if you had done a search you would have found all of the above written by me many, many times.

Aftermarket injectors designed for use on other engines (that may or may not require adaptors to fit RB25’s) may or may not be specified for the same fuel pressure. Their operating and flow rating are specified. BUT (there is always a but) I have not found any injectors that use different fuel pressures that will fit RB25’s

let me help you out then, HKS, Sard, Apex

I havent done the testing myself, just basing this on what has been published (by AP racing) and what I have been told by signal japan - all rated and should be run on 3.0kg base pressure at idle. This was based on trial and error, as explained to me, especially with larger injectors, its difficult to get a nice idle with factory fuel pressure - can be done, but its easier (and better) to use 3.0kg - but hey, they are probably just a bunch of dump Japanese, what would they know.

Another thing to remeber, if you fit say sard 550cc injectors, and only run the factory base fuel pressure, the injector correction and lag adjustment will be different (510cc v's 550cc, +0.06ms vs +0.08ms)

- or dont you consider this an important factor?

let me help you out then, HKS, Sard, Apex

I havent done the testing myself, just basing this on what has been published (by AP racing) and what I have been told by signal japan - all rated and should be run on 3.0kg base pressure at idle. This was based on trial and error, as explained to me, especially with larger injectors, its difficult to get a nice idle with factory fuel pressure - can be done, but its easier (and better) to use 3.0kg - but hey, they are probably just a bunch of dump Japanese, what would they know.

Another thing to remeber, if you fit say sard 550cc injectors, and only run the factory base fuel pressure, the injector correction and lag adjustment will be different (510cc v's 550cc, +0.06ms vs +0.08ms)

- or dont you consider this an important factor?

2.5 bar rail pressure plus the normal 0.5 bar vacuum at idle = 3.0 bar

:P cheers :D

Edited by Sydneykid

what the?

sorry, not following what you are saying

nissan manuals state stock rail pressure as 2.55kg at idle, 3.05kg at atmosphere, their injectors are rated at 2.55kg, ie, idle (rb25 - 370cc at 2.55kg, 410cc at 3.05kg etc)

Sard, apex, hks rate their injectors at 3.0kg at idle

how are these the same????

what the?

sorry, not following what you are saying

nissan manuals state stock rail pressure as 2.55kg at idle, 3.05kg at atmosphere, their injectors are rated at 2.55kg, ie, idle (rb25 - 370cc at 2.55kg, 410cc at 3.05kg etc)

Sard, apex, hks rate their injectors at 3.0kg at idle

how are these the same????

Nissan (and Nismo) know that the RB produces 0.5 bar at idle, hence they can specify 2.5 + 0.5 = 3.0.

Sard, Apexi, HKS only know what their injectors flow at 3.0 bar, so that's the only number that they can specify. Keep in mind that Jecs make Nissan annd Nismo injectors and Denso make pretty much everything else.

Real world proof, if I stick a 550 cc Nismo injector on the flow bench at 3.0 bar and compare it with a 550 cc Sard injector at 3.0 bar, I end up with pretty much the same flow rates (ie; ~550 cc per minute).

There are exceptions, Rochester for example.

:) cheers ;)

OK, he says puting his hand up, that would be me.

Aftermarket injectors (eg; Nismo) designed for use with RB25’s use the standard Nissan fuel pressure, which is 34-36 psi (2.3 to 2.5 bar). Aftermarket injectors designed for use on other engines (that may or may not require adaptors to fit RB25’s) may or may not be specified for the same fuel pressure. Their operating and flow rating are specified. BUT (there is always a but) I have not found any injectors that use different fuel pressures that will fit RB25’s.

So while you are right in theory, in the real world that is simply not the case.

Plus I defy anyone to tell the difference in spray patterns between 2.5 and 3 bar base pressure. Remember injectors in turbo engines have to have good spray patterns at absolute pressures ranging from 2.0 to 6.0 bar (plus or minus vacuum and boost). So 0.5 bar is neither here nor there as far as their spray pattern is concerned. This is not always the case in injectors intended for N/A use however. Rochesters for example, like to have their specified fuel pressure at all times and don’t handle drastic increases or decreases.

Back to the original question. With a perfect tune and an engine in perfect condition the standard injectors are OK for around 225’ish rwkw (300 rwhp). But I have only seen that once in over 50 R33GTST’s. The rest have dropped off from 205 rwkw (275 rwhp) onwards, with around 215 rwkw (290 rwhp) being the most common.

An adjustable FPR (eg; Nismo bolt style $150 from Nengun) will facilitate an increase in fuel pressure. It isn’t linear though, a 10% increase in pressure doesn’t equal a 10% increase in flow. For example increasing the base pressure to say 46 psi (30%) enables the standard injectors to stretch to around 400 cc’s (up from 370 cc which is 8%). That’s enough for 235 rwkw (320 rwhp) which his about as far as I would recommend going. The fuel pressure gets too high for the standard size hoses and clamps and fuel fires are very nasty. Hence why I suggest replacing the 10 + year old fuel hoses with new ones. Plus Walbro pumps are not very good at handling pressure, their flow drops off rather dramatically.

A spot 97% injector duty reading is not a very good indication, it may well have been 85% duty, plus 12% for acceleration enrichment. Try looking at the injector duty as you run up through the rpm range at WOT in 3rd and 4th gear (a passenger is handy for that). That is a far better indicator.

The GCG high flow is good for around 265 rwkw (355 rwhp). So if you want to use the full potential of the turbo upgrade you really need to be looking at aftermarket injectors.

Hope that was of some help

:( cheers ;)

PS; if you had done a search you would have found all of the above written by me many, many times.

What sort of power can the walbro pumps handle up to? or are you saying their not very reliable from the word go?

Btw, i have read many of your post's sydneykid, they are most helpful!

but nissan fuel pressure at idle is 2.55kg, not 3kg - thus why I was saying a fuel pressure reg is worthwhile.

Yes, but it has 0.5 bar of sucking (vacuum) helping the injectors flow. Hence the "real" pressure is 3.0 bar. The 3.0 bar is the pressure differential between the fuel rail and the inlet port.

As usual the numbers tell the story;

2.5 - -0.5 = 3.0

The 3.0 bar is the pressure differential between the fuel rail (2.5) and the inlet port (-0.5).

Same applies when there is boost in the inlet port, except boost is a "+" of course

4.0 - + 1.0 = 3.0

The 3.0 bar is the pressure differential between the fuel rail (4.0) and the inlet port (1.0).

:( cheers ;)

What sort of power can the walbro pumps handle up to? or are you saying their not very reliable from the word go?

Btw, i have read many of your post's sydneykid, they are most helpful!

Do a search “Sydneykid”, Walbro” and “any date”. I have posted up the test results of what happens to the flow of a Walbro pump when it has to pump against boost pressure.

:( cheers ;)

well if that be the case, factory RB25 injectors would flow 410cc, but they dont, they are 370cc -

RB25/SR20 -- stated inj flow, 370cc, tested at 2.55kg - 370cc, at 3.05kg - 410cc

Sard 550cc -- stated inj flow, 550cc, tested at 2.55kg - 510cc, at 3.05kg - 560cc

Apexi 740cc -- stated inj flow, 740cc, tested at 2.55kg - 675cc, at 3.05kg - 740cc

Now why would nissan rate their injectors lower than they actually are, because following your logic, they are in fact 410cc, not 370...

AP engineering and Nissan are obviously wrong, following your theories.

For those interested, with thanks to AP engineering (and cubes for copying them before they went off line :( )

Very handy reference, esp for caclulating injector correction and lag time correction

Top feed (sorry about the small size, if you right click and save image as, you can easily zoom in - for those interested anyways)

TopFeed.gif

Side feed

Sidefeed.gif

Hi Guys , im in the situation where i am upgrading injectors + z32 AFM and Nismo Fuel reg + apexi super intake filter

Should i consider upgrading my fuel hoses.

Im running at the moment

PFC

AVCR

R33 standard hiflow plain bearing (12psi)

Walbro fuel pump

Split dump to hiflow cat.

I have 306rwhp, i am upping the boost to 15psi when i get my tune.

I also have oil cooler kit, oil catch can, getting put on by myself after tune has been done.

I just saw that word fire, and yeah not a big fan.

So anything that i can get for my car to be relatively safe , would be pretty helpful.

And Letemlaf, my car is pretty much on 65% duty and my afm is close to maxin out. on 306rwhp. And yeah getting the other stuff being put on next week, by one of the best performance places i have been too.

i'll let ya know how it goes, and if my car catches on fire or blows up.

Look at them, and see if they are in good condition or not (no signs of bulging/cracking etc). If they look tired, replace them - they should be inspected when you service the car, but sometimes people get lazy.

I made over 400rwhp with stock fuel lines, but I did preplace the rubber hoses that run to/from the fuel rail, because they looked a bit tired.

Injectors are not going to get you there.

You need to upgrade your turbo and make sure all your supporting mods are there for the power level....

ie.Oil cooler for oil,catch can,etc,etc....

You also do not have a boost controller.so you will need one withthe new turbo

So before you change injectors and spend all that money on fuel mods. get the power up.

I am a bit confused too...are you saying your injectors are maxing out or are you asking

us if they would be.....the answer is no with the mods you have.

Cheers ;)

Injectors are not going to get you there.

You need to upgrade your turbo and make sure all your supporting mods are there for the power level....

ie.Oil cooler for oil,catch can,etc,etc....

You also do not have a boost controller.so you will need one withthe new turbo

So before you change injectors and spend all that money on fuel mods. get the power up.

I am a bit confused too...are you saying your injectors are maxing out or are you asking

us if they would be.....the answer is no with the mods you have.

Cheers ;)

Yeah, i was a little confused because my workshop said they will be right on the limit and from what ive read on here they should be good for alot more power than what i have.

I just replaced my fuel filter because it was over due, from what i can tell i am hitting about the 89% duty in 3rd gear. But ill see how it goes over the next few days

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, I can recommend the partial AV system translation CD I ordered from Car Audio Workshop in NZ. Whilst it didn't address the date issue, it has conveniently translated on-screen menu items into English, and now allows the GPS-received time to be offset in hours rather than minutes, so I can display Eastern Australian time accurately ( and bump it by another hour when daylight savings starts ).
    • Yuh, if it's 45°C outside, my car is driving in it.
    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
×
×
  • Create New...