Jump to content
SAU Community

F.s. Z32 Afm With Plug New

skyhi747
 Share

Recommended Posts

skyhi747 Apprentice

skyhi747

Posted
Posted

Hi i'm selling my Z32 AFM with brand new plug.. i'm after $330 for it firm... please pm me if anyone is interested. I dont think theres a cheaper one anywhere.. No longer need due to upgrade ecu which doesn't req afm.. was going to buy power fc but got wolf at cheaper price. Cheers!

post-30902-1162334493.jpg

Link to comment
https://www.sau.com.au/forums/topic/141319-fs-z32-afm-with-plug-new/
Share on other sites
skyhi747 Apprentice

skyhi747

Posted
  • Author
Posted (edited)
Is the afm also new or is it just the plug thats new?

The afm is brand new aswell.. i dont really trust 2nd hand electronic stuff thats got to do with engine management but i dont need it nemore cos of the wolf so yea.. i've just taken the afm out of the plastic to take the photo... if your interested pm me dude.. oh and i'll send it anywhere in aus for $10 express post.

Please feel free to ring around to find out how much they're worth... i need the money for tune so i'd like to get rid of this asap.

Part # for Z32 is F00E000202.. retails at around $430.00

Part # for Plug is 1287013004... retails at around $61.00

Edited by skyhi747
skyhi747 Apprentice

skyhi747

Posted
  • Author
Posted
Is it the type that hooks up to the standard skyline intake pipe? or is it just oem z32 version. Also did you buy off this forum.

yea dude its the same size as the standard one as in what it connects to like intake pipe and pod filter... the plug i have needs to be re wired as all do... but nah i didnt get it from this forum... but i figured cos other ppl are selling em brand new for $330 and $45 for the tomei plug i thaught i shouldn't have an issue selling for $330 with the bosch plug included.. well its still for sale but i've got it advertised in a few places i'm really eager for tune but need the $$

cheers

george

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...