Jump to content
SAU Community

Recommended Posts

Recently i have been seriously looking for a bigger turbo for my car, but wasn't too keen on the lag factor. My aim to to acheive 280-320rwkw, but i would like to keep it's drivability.

B4 i go on: i have done a comprehensive search and wasn't able to find anything on this issue, so please if you know of a thread post it up below.

For those in the know i would REALLLLLY appreciate your input and advise, i am all "ears"!

My idea is to replace my turbo and manifold with a twin turbo setup (gtr style). By using 2 smaller turbos (350hp each) this should, i think, produce about 400kw at the crank.

MODIFICATIONS (Things i know that need replacement):

-New manifold (Can a GTR manifold fit on the RB25det head?)

-Custom front pipes

-Dual oil/water cooling lines for turbos (can the original line be split into two to cool both?)

-Custom intake pipes (from filter to turbo and from turbo to fmic)

CURRENT MODS:

-Wolf 3D V4.51 R33 Plugin

-Fount Mount Intercooler

-Cold Air induction (Pod in sealed partition with 4" drain pipe feed from front bar.

-Adjustable boost

-3" hi-flow exhaust system from turbo

-H/D clutch

MODS TO BE COMPLETED WITH UPGRADE

-550cc injectors

-bosch fuel pump

-bosch fuel regulator

-Ceramic coating of all piping (ex. manifold, intercooler pipes, turbo cover, plenium, exhaust from turbo to cat., etc)

-ADJ. ex. cam gear (optional)

QUESTIONS:

-Is this project possible and financially fissable?

-Which turbo's would best do the job?

-Any other mods that you would recommend doing (cams, etc.)?

-Has this been done B4?

-How does the GTR manifold work? Does it use 3 cylinders per turbo?

-Any other information/points are most welcome.

Again, i would REALLY appreciate everyones input and like to say

THANKS in advance.

ALAN C.

Link to comment
https://www.sau.com.au/forums/topic/14153-hlep-considering-bulding-a-rb25dett/
Share on other sites

OK high power and lag go hand in hand un less you increase capacity sso you want 280-320 rwkw with boost down low the best way to do this is with an rb 25/30 motlowth on hearhas a similar set upto what you want and thats how he did it the twin turbo's are possible but you will still have lagg.

he is making 310-320 rwkw @ 1 bar full boost by 4 k rpm I believe

meggala

btw go to my web site and read the mods section It might help

Hi Nismo_Boy, how about we cost this idea...

MODIFICATIONS

-New manifold $1200

no a GTR one won't fit.

-Custom front pipes $800

-Dual oil/water cooling lines for turbos $300

-Custom intake pipes $400

MODS TO BE COMPLETED WITH UPGRADE

-550cc injectors $800

-bosch fuel pump $500

-bosch fuel regulator $300

- Ceramic coating of all piping $700

- ADJ. ex. cam gear $250

- 2X hi flowed RB25 turbos $2200 each

- Dyno tune $400

That's a nice round $10,000 but the RB25 internals won't handle 320 rwkw, so you will need...........

- forged pistons $2000

- conrods $2200

- balance, gaskets, seals, o'ring block say $1800

- oil cooler $900

- radiator upgrade $1000

- camshafts $1600

- porting of cylinder head $700

And that totals $19,850.

When do you want to start?

THANKS FOR ALL YA INPUT GUYS!!

Looks like i need to go back to the single turbo idea, as the deal with NISMO_BOY may fall through. It was pure coinsidance that he was selling this setup at the time i posted this idea. But i consider $4000 for basically a block, manifold (modified rb26DETT) and 2 worn turbos a bit rich, not to mention risky.

But now i am back to my original delema. What turbo will best do the job and has the least lag? I am under no illusion that i will get more lag, just want the best package.

Originally posted by Sydneykid

Hi Nismo_Boy, how about we cost this idea...

MODIFICATIONS  

-New manifold $1200

no a GTR one won't fit.

-Custom front pipes  $800

-Dual oil/water cooling lines for turbos $300  

-Custom intake pipes $400  

MODS TO BE COMPLETED WITH UPGRADE  

-550cc injectors $800

-bosch fuel pump $500

-bosch fuel regulator $300

- Ceramic coating of all piping $700  

- ADJ. ex. cam gear $250

- 2X hi flowed RB25 turbos $2200 each

- Dyno tune $400

That's a nice round $10,000 but the RB25 internals won't handle 320 rwkw, so you will need...........

- forged pistons $2000

- conrods $2200

- balance, gaskets, seals, o'ring block say $1800

- oil cooler $900

- radiator upgrade $1000

- camshafts $1600

- porting of cylinder head $700

And that totals $19,850.

When do you want to start?

Why would i want to start, when i can just buy the one im selling for $4k

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...