Jump to content
SAU Community

Fs: Cefiro Bits/s13/c33/180 + Dish And Aftermarket Bits

Hella Flush
 Share

Recommended Posts

Hella Flush Experienced

Hella Flush

Posted
Posted (edited)

full 4 stud hubs brakes and stub axle setup front and rear

safety21/cusco 6 point full cage - good for street as it follows all roof and pillar lines

navy blue a31 unregistered/uncomplied 88' cefiro... factory 5 spd manual turbo... fresh 8X,XXXkm engine dropped in - gtr 33 cooler, gtr fuel pump, nismo clutch, eastbear cooler piping etc... many mods can come with it - pm for enquiry/package - has import approval so can be complied easily

fiberglass front and rear fender flares universal - arch type... with rubber seals and stainless hex bolts

random other ceffy shit... series 1 tailights with cefiro written in the middle

kei office front and rear coilovers - height and preload adjustable with front camber tops - need rear tops...

Edited by Hella Flush
NV N01 Experienced

NV N01

Posted
Posted
willing to ship thats no problems aslong as you pay for freight

It might cost a bit to send a whole car up with a cage and coilovers?

Hella Flush Experienced

Hella Flush

Posted
  • Author
Posted

photos can be found here of cage

http://i66.photobucket.com/albums/h252/1at...-10-06_12-1.jpg

http://i66.photobucket.com/albums/h252/1at...22-10-06_12.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      ZF 6HP26 to RB30 block

      By joshuaho96 · Posted

      Most people I know in the BMW world are swapping 6HPs for 8HPs. The 6HP has a big issue with one of the clutch drum bushings wearing out shockingly early which leads to them going into limp mode going into 5th/6th gear as the oil pressure loss from the worn bushing causes clutch slip. Even with the adaptations in shifting the TCU can't bump line pressure enough to keep the clutches from slipping and burning. I've personally looked at a 335d with 6HP28 with one owner and ~90k miles on it and the transmission adaptations were way out of spec and even though it nominally drove ok I'm confident it would have needed a full rebuild sooner than later. Other than that they're fine, but the 8HP doesn't really have weird issues like this to my knowledge and they're in everything these days so pulling them out of crashed cars isn't too hard.
    • joshuaho96
      R34 GT-T cycling ABS pump

      By joshuaho96 · Posted

      There is an ABS pump and a few solenoids. You could trigger the front/rear solenoids with a pressure bleeder attached with a Consult 2. 
    • Dose Pipe Sutututu
      R33 GTST Sh*tbox to Polished T*rd

      By Dose Pipe Sutututu · Posted

      I love saying Samsonas lol. Maybe it's because I secretly want one, but also don't want to sell a kidney.
    • Yeetus
      R33 GTST Sh*tbox to Polished T*rd

      By Yeetus · Posted

      My budget has already blown way out but I've got most of the big-ticket items out of the way haha I just got the box back from the shop, got them to inspect it and install one of those refresh kits with all new syncros and bearings so should feel much nicer. But yeah if there's a weak point it'll be the gearbox, I'm gonna roll with it for now and hope it holds together. Do have an Xtreme organic sprung twinplate clutch to go in so if/when the box lets go I'll be back open for suggestions haha
    • GTSBoy
      R33 GTST Sh*tbox to Polished T*rd

      By GTSBoy · Posted

      Dose salivating at the prospect of being able to recommend a gearbox upgrade!
×
×
  • Create New...