Jump to content
SAU Community

Recommended Posts

Cefiro/S13 coilovers, 4 stud rims prefer 17x8/9 or similar. Also after heat shields for manifold and turbo RB20.

PM me if you have something i might be interested in.

i got rb20 heat shield, well the cover and the bracket, maybe missing a few bolts shoulda said when you brought the water lines. ill give it to ya for 15bux too if you want it

need R32 gtst m spec side skirts and rear pods

not fussed on colour, got spray cans here at home

but need to be in good condition and need by next weekend

pm me

also jms_31 got the afm here, $50 and you can have it, i also pm'ed u

Front lip spoiler for stock series 2 front bar

Anyone know anyone that has one let me know

Cheers

I've got one. I had to buy a whole front bar for regancy and its got the front lip and D1 vents also. Send me a PM if your keen, I do need it for a bit longer atm tho. Cheers

Hey guys,

I have a series 2 R33 with Bilstein shocks and superlow springs all round, I wish to be at legal height so I'm looking for some springs. My car currently sits eyebrow height 330 all round. Has anyone got some legal height springs laying around that I can buy?

Cheers Simon

Hey im in need of r34 GTR bov's and piping or any bov's and piping for a rb26dett. It has to have the recirculation piping from the bov's back into the engine as i need it to be full plumb back. need it to pass the pits. please pm me. even if someone has some which i can borrow it would be great.

Cheers

David

Hey im in need of r34 GTR bov's and piping or any bov's and piping for a rb26dett. It has to have the recirculation piping from the bov's back into the engine as i need it to be full plumb back. need it to pass the pits. please pm me. even if someone has some which i can borrow it would be great.

Cheers

David

hey bro. i rang clinton at vehical standards about bovs few weeks ago.

all bov must be stock no exceptions. not even plumb backs.

that screwed me also so i took it off.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...