Jump to content
SAU Community

Recommended Posts

I had my old 33 shooting HUGE flames when I had a 3inch pipe. That is right I didnt have and exhaust and a muffler, it was a 3inch pipe with a bit of sheetmetal welded around the back to look like a muffler, was awesome, from 2nd to 3rd or 3rd to 4th, just let of the trottle and take an extra second or two on the change and BAM! :(

vidsorban of stagea flamage!! :)

Dump pipe, front pipe, no cat, little hot dog muffler then canon Apexi rear muffler with removable silencer in place.

Still running the stock auto ecu but with an Apexi SAFCII that needs a tune to lean it out a bit more.

It pops and farts on engine braking as well. It feels so much more powerful with the manual.

I will have a go at getting some pics but it could be a bit tricky.

Yep Revzone did the work so they know hot to do it all now. I had a few issues with some late and missing parts from Nissan so it’s not finished yet, just at a level that is drivable. The hand brake isn’t mounted, no boot on the gear leaver so I have a hole in the floor etc.

Component Cost

Gear box 2nd hand $1,300

Fly Wheel $0

Hand Brake 2nd hand $0

Hand Brake bracket $47

Clutch New $320

Clutch Line New $120

Master Cylinder New $130

Clutch Pedal New $80

Clutch Pedal bracket New (Stagea) $112

Pedal box R33 to Cannibalise 2nd hand $280

Slave Cylinder New $95

Spigot Bearing $25

Bolts $100

Brake Fluid $50

Labour $900 est

Total So far $3,559

Left to do:

Gear Oil $60

Gear leaver Boot rubber and Plate $150

Bear boot leather $100

Gear Knob $50

Shift Leaver / Shift Forks $300

$660

Finished total $4,219

I will see if I can make it to the meet but wont be able to do the whole cruse.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...