Jump to content
SAU Community

Recommended Posts

I had my old 33 shooting HUGE flames when I had a 3inch pipe. That is right I didnt have and exhaust and a muffler, it was a 3inch pipe with a bit of sheetmetal welded around the back to look like a muffler, was awesome, from 2nd to 3rd or 3rd to 4th, just let of the trottle and take an extra second or two on the change and BAM! :(

vidsorban of stagea flamage!! :)

Dump pipe, front pipe, no cat, little hot dog muffler then canon Apexi rear muffler with removable silencer in place.

Still running the stock auto ecu but with an Apexi SAFCII that needs a tune to lean it out a bit more.

It pops and farts on engine braking as well. It feels so much more powerful with the manual.

I will have a go at getting some pics but it could be a bit tricky.

Yep Revzone did the work so they know hot to do it all now. I had a few issues with some late and missing parts from Nissan so it’s not finished yet, just at a level that is drivable. The hand brake isn’t mounted, no boot on the gear leaver so I have a hole in the floor etc.

Component Cost

Gear box 2nd hand $1,300

Fly Wheel $0

Hand Brake 2nd hand $0

Hand Brake bracket $47

Clutch New $320

Clutch Line New $120

Master Cylinder New $130

Clutch Pedal New $80

Clutch Pedal bracket New (Stagea) $112

Pedal box R33 to Cannibalise 2nd hand $280

Slave Cylinder New $95

Spigot Bearing $25

Bolts $100

Brake Fluid $50

Labour $900 est

Total So far $3,559

Left to do:

Gear Oil $60

Gear leaver Boot rubber and Plate $150

Bear boot leather $100

Gear Knob $50

Shift Leaver / Shift Forks $300

$660

Finished total $4,219

I will see if I can make it to the meet but wont be able to do the whole cruse.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...