Jump to content
SAU Community

32 Boost Doesnt Seem To Be Right

kingy_06

By kingy_06,
in Engines & Forced Induction

 Share

Recommended Posts

kingy_06 Enthusiast

kingy_06

Posted
Posted

hey, i have a R32 gtst type M! The mods are apexi pod filter and and 3" cat back exhaust (i dont know this for sure though when look under car it is obvious that from the cat back the exhaust is larger then cat to turbo!) I just installed a boost gauge and it is reading 10-11PSI in all gears and holds this! My car does not have a boost controller! Is this boost right as i thought it was a bit high! Do type M run a bigger turbo or more boost? Any help would be great!

Cheers,

Tyson

Link to comment
https://www.sau.com.au/forums/topic/144046-32-boost-doesnt-seem-to-be-right/
Share on other sites
kingy_06 Enthusiast

kingy_06

Posted
  • Author
Posted

thanks mate, did some searching though eveyone has there own say on 32 boost.....it stock 7PSI....stock 10PSI

One more questions: I have done heaps search on 32 boost and need some advice! I am going to get the rest of my exhaust done so (dump and front and high flow cat) so it will be a full 3" system...the car will prob run about 11PSI then! Should i get a boost controller and up the boost to 12PSI - dont want to go any higher than this, and get a front mount! or buy a 33 or 34 turbo to get more boost?

Cheers

123456 Proficient

123456

Posted
Posted

Upping it to 12 won't hurt but the standard turbo gets boring pretty quickly, so buy a cheap boost controller, and crank the psi to 12 after you've put the exhaust on, and run around on that while you save for a better turbo. Standard rb20 turbo @ 12 psi is preeety boring

Josh_r32 Rising Star

Josh_r32

Posted
Posted (edited)
Yep 12psi is pretty boaring through the rb20's.

I pushed mine to 1bar without issues for a few years before the new motor was dropped in. Old motor was 100% still fine as was the turbo when it came out.

wat mods did you have when you ran it on 1 bar? did you still have stock internals?

also on the stock boost gague in a r32 gtst type-m, the -7 and +7 on the boost gague

does that refur to psi or does +7 mean 0.7 bar or 7pi pr wat? if thry run 10psi stock, why does

the gague only go up to 7?

Edited by Josh_r32
Cubes Grand Master

Cubes

Posted
Posted

The car just had a full exhaust, fmic and had boost wound up on the dyno. AFR's showed they were leaning out so a new fuel pump went in. It was then advanced 2 degree's and wasn't pinging on the dyno even though temps were 30degree's.

On the stock guage.. Mine was a little out, with the needle almost ready to topple over the +7 top line that was 15psi.

Have a look at the std guage it tells you the units of measurement used.

+7 is supposed to be around 13.5psi from memory. As I said mine was out a little.

kingy_06 Enthusiast

kingy_06

Posted
  • Author
Posted

thanks for all the replies! I have to agree, atm the stock rb20 turbo is boring! I will get my exhaust done and up the boost to 12 PSI Should i get an intercooelr after this? (will it give more power) or look at a 33 or 34 turbo?

thrtytwo Veteran

thrtytwo

Posted
Posted
thanks for all the replies! I have to agree, atm the stock rb20 turbo is boring! I will get my exhaust done and up the boost to 12 PSI Should i get an intercooelr after this? (will it give more power) or look at a 33 or 34 turbo?

im not an expert so im not 100% sur ebut i think any increase in boost should warrant a FMIC, even if it isnt totally needed it looks cool and is usefull if you want to go further later on, lots of ppl use turbos from 33's, stock or highflowed, never heard of anyone using from a 34 but dunno if u cant or what...would of thought it weas same turbo as 33, probably just more expensive...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...