Jump to content
SAU Community

32 Boost Doesnt Seem To Be Right

kingy_06

By kingy_06,
in Engines & Forced Induction

 Share

Recommended Posts

kingy_06 Enthusiast

kingy_06

Posted
Posted

hey, i have a R32 gtst type M! The mods are apexi pod filter and and 3" cat back exhaust (i dont know this for sure though when look under car it is obvious that from the cat back the exhaust is larger then cat to turbo!) I just installed a boost gauge and it is reading 10-11PSI in all gears and holds this! My car does not have a boost controller! Is this boost right as i thought it was a bit high! Do type M run a bigger turbo or more boost? Any help would be great!

Cheers,

Tyson

Link to comment
https://www.sau.com.au/forums/topic/144046-32-boost-doesnt-seem-to-be-right/
Share on other sites
kingy_06 Enthusiast

kingy_06

Posted
  • Author
Posted

thanks mate, did some searching though eveyone has there own say on 32 boost.....it stock 7PSI....stock 10PSI

One more questions: I have done heaps search on 32 boost and need some advice! I am going to get the rest of my exhaust done so (dump and front and high flow cat) so it will be a full 3" system...the car will prob run about 11PSI then! Should i get a boost controller and up the boost to 12PSI - dont want to go any higher than this, and get a front mount! or buy a 33 or 34 turbo to get more boost?

Cheers

123456 Proficient

123456

Posted
Posted

Upping it to 12 won't hurt but the standard turbo gets boring pretty quickly, so buy a cheap boost controller, and crank the psi to 12 after you've put the exhaust on, and run around on that while you save for a better turbo. Standard rb20 turbo @ 12 psi is preeety boring

Josh_r32 Rising Star

Josh_r32

Posted
Posted (edited)
Yep 12psi is pretty boaring through the rb20's.

I pushed mine to 1bar without issues for a few years before the new motor was dropped in. Old motor was 100% still fine as was the turbo when it came out.

wat mods did you have when you ran it on 1 bar? did you still have stock internals?

also on the stock boost gague in a r32 gtst type-m, the -7 and +7 on the boost gague

does that refur to psi or does +7 mean 0.7 bar or 7pi pr wat? if thry run 10psi stock, why does

the gague only go up to 7?

Edited by Josh_r32
Cubes Grand Master

Cubes

Posted
Posted

The car just had a full exhaust, fmic and had boost wound up on the dyno. AFR's showed they were leaning out so a new fuel pump went in. It was then advanced 2 degree's and wasn't pinging on the dyno even though temps were 30degree's.

On the stock guage.. Mine was a little out, with the needle almost ready to topple over the +7 top line that was 15psi.

Have a look at the std guage it tells you the units of measurement used.

+7 is supposed to be around 13.5psi from memory. As I said mine was out a little.

kingy_06 Enthusiast

kingy_06

Posted
  • Author
Posted

thanks for all the replies! I have to agree, atm the stock rb20 turbo is boring! I will get my exhaust done and up the boost to 12 PSI Should i get an intercooelr after this? (will it give more power) or look at a 33 or 34 turbo?

thrtytwo Veteran

thrtytwo

Posted
Posted
thanks for all the replies! I have to agree, atm the stock rb20 turbo is boring! I will get my exhaust done and up the boost to 12 PSI Should i get an intercooelr after this? (will it give more power) or look at a 33 or 34 turbo?

im not an expert so im not 100% sur ebut i think any increase in boost should warrant a FMIC, even if it isnt totally needed it looks cool and is usefull if you want to go further later on, lots of ppl use turbos from 33's, stock or highflowed, never heard of anyone using from a 34 but dunno if u cant or what...would of thought it weas same turbo as 33, probably just more expensive...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      first time swapping rb25det into r34

      By GTSBoy · Posted

      Let me assume that the concern over a manual ECU is that the NeoDET that you have was an auto and has an auto ECU. That ECU will not be a problem, but you WILL have to Nistune it. And you would have to Nistune it even if you had a manual ECU, because the turbo ECUs will shit the bed if they do not have all the things that they were told they have to have, to be happy. The big one being the TCS CU, which you won't have in your car. Anyway, with an auto ECU (which I have running my originally auto NeoDET in an R32) Nistune allows you to put in a Stagea image which doesn't panic about the absent TCS, and allows you to override a whle bunch of other annoyances that would otherwise see the check engine light on 100% of the time. Also, you can't wind up the power very far on the stock NeoDET ECUs without Nistune, because the boost sensor gets in the way. Nistune allows you to push that problem much further up the dial. Do you even have the boost sensor with the engine? Without it, you are SOL and will need an aftermarket ECU (or to find a sensor somewhere, god knows where). I can't tell you what the wiring loom differences are in a 34. But what Duncan said above needs to be considered. When you say "loom", does that include the transmission loom? Because you will need to swap out the auto tranny loom for the equivalent manual loom, and get rid of the neutral/park start interlock (basically hot wire it).
    • WR33KD
      Ogura orc1000f vs Osg tr2cd vs Osg r3c experiences, max torque/max hp?

      By WR33KD · Posted

      I have had the r3c in for years now, maybe close to 7 years and it has never missed a beat, anyone can drive it. Super easy to drive around town, the hotter it gets does get a little hard but it holds the power easy as 
    • Duncan
      Rusty roof repair

      By Duncan · Posted

      Shit thing to find eh? I guess the big issue is that whatever "fix" you do now, it might slow the rust down but won't fix it. I just wanted to add that in no way is fixing sheet metal in 3 dimensions the place to start with welding....that is a pro only job because its too hard to work out where things should be, let alone doing a clean enough job that it can look OK and still be strong too.  I needed to get a new rear quarter panel on the GTR and it took a pro weeks to get the old one off cleanly, new one on in the right place and looking somewhat like it should have with most of the previous connecting panels in place. Gluing a couple of bits of metal together with a welder in the garage is doable, but that is totally different to doing panel  replacement
    • Duncan
      first time swapping rb25det into r34

      By Duncan · Posted

      This seems to be a very popular swap since all the turbo skyline prices went through the roof! I'll let someone more familiar chime in, but I understand that yes you probably want to swap the loom in to swap out the auto TCM stuff. You should not assume everything just plugs in either, you need to check at least the ECU wiring diagram for any differences at the plug at the left headlight and probably the ones near the ECU that join the dash loom too  
    • dingleberry
      first time swapping rb25det into r34

      By dingleberry · Posted

      hows it fellas, my first post here which seems crazy cos half the forums i read are like the same age as me haha. to make a long story short ive got an r34 sedan (rb25de neo auto) which im swapping to a s0/s1? rb25det, r33 big box and nismo gt pro lsd. i have the motor and gearbox all bolted up outside the car, old motor and trans out. i bought the motor with stock ecu and loom, do i switch over to that? or will it be easier to get a r34 manual ecu and keep the loom if thats even possible.  also engine mounts look different, anything else thats different or incompatible? cheers, hope this all makes sense Paddy
×
×
  • Create New...