Jump to content
SAU Community

Wtb: Standard Cooler Piping Off A R32 Or 33.


Recommended Posts

hi every one from launcestion (joke)

im after some standard cooler piping off a r32 or 33. just the few tight curvs that plumb onto the standard cooler.

if any one has some please let me know.

thanks damo

i have a lil box of goodies but wouldnt have a clue what you need, i dont talk 'skizza' very well, but I'm learning. I have a standard intercooler here in my box and a few bits of rubber pipeing corners or something...ah hell I have no idea whats in the box!

heres a pic, if it isnt what you need, can you tell me what it is from this dodgy photo?!

28-11-06_2207.jpg

well im after the standard steal bends that twist around the standard cooler. i know my 32 has steal pipes but not real sure on 33s.

the bend at the bottom of the pic looks steal but maybe not. thats what im after anyway.

thanks damo

hey guys. yea im just after the pipe with bends in it. ive got an r32 GTR cooler and im going to use standard cooler pipe bends and some straight tube and ill have it plumbed up in not time. not the prettyest way to go but a good cheap but not dodgy option. so if yyou have a bend or to send me a msg with how much cash you want for it and we will sort somthing out.

thanks damo

hey john yea its me damo. im trying to get my front mount on. yea im keen for the standard ones if you have them floating about. mild steel would be better. where would i be able to colect them from john?

thanks damo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...