Jump to content
SAU Community

Recommended Posts

hey guys ill be getting new turbos next week and wana get the gasket kit. but not sure which gaskets i need for a turbo change over. ill just be getting hi flows. i found these on the justjap website for $250. are these all the gaskets i need to swap over my turbo with the new hi flows on my 32 gtr ?

hksgasketkitrb26.jpg

ill be getting new dump pipes so that should cover the gaskets for the dumps. if you know other places to get them for cheaper as a whole kit of everything i need (not necessarily brand name but quality stuff) let me know too! oh and i believe i also need new studs and bolts?

can anyone list me all the parts required (gaskets/bolts) i need (and where to get / price) to jus give the mechanics so they can do it all in one go?! as i dont wana muck around getting parts for this and that while waiting!

thanks!

Link to comment
https://www.sau.com.au/forums/topic/146476-gtr-gaskets/
Share on other sites

Those gaskets you pictured do:

a) plenum to throttle bodies.

b) throttle bodies to head.

c) head to exhaust manifolds.

None or which should need to be changed for replacing the turbos.

b) Is actually inlet mannifold to head. There are 2 lots of 3 throttle body gaskets. One set for plenum and one set for inlet mannifold.

You will need to replace the head to mannifold gaskets if they break. These have to be unbolted during the job. If they dont break you can reuse them with some ultra blue. You can reuse the crush gaskets that join the dumps to the turbos a few times. Check them for leaks and perhaps use copper coat on them.

Deren

Link to comment
https://www.sau.com.au/forums/topic/146476-gtr-gaskets/#findComment-2739404
Share on other sites

My apologies.

Deren's right there, just checked the service manual and it says to remove the exhaust manifolds when swapping turbos. Happily haven't had to do that yet.

Still, thats 2 out of the whole set. It would be better to only get what you need.

James

Link to comment
https://www.sau.com.au/forums/topic/146476-gtr-gaskets/#findComment-2739420
Share on other sites

Hanyou, what you will possibly need are the Head to manifold gaskets (the 2 top ones) the manifold to turbo (not pictured) and the exhaust housiing to dump (not pictured). You can also get the dump to engine pipe but I use super copper gasket goo.

Go to GCG. I once bought all that lot from Nissan for $400..... :(

Link to comment
https://www.sau.com.au/forums/topic/146476-gtr-gaskets/#findComment-2739481
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...