Jump to content
SAU Community

Recommended Posts

I actually defeated a "failure to obey an officer" or whatever.

because he wasnt in uniform :laugh:

He didnt have

1) A hat

2) reflective vest while directing traffic

3) Shoulder lapels.

I went on the argument he looked like a hot and bothered bus driver.

And winner to me :(

The judge actually hammered him. He had been in the force for 20 years and should have known better.

Power to the people :laugh:

Thats not the issue here. You got off because the officer failed to correctly identify himself, not because he wasnt in uniform. They are not the same thing, how else do you think plain clothes officers and detectives are able to execute their duties?

Original poster...Good luck with it all :)

Note to self: underwear on head is bad ;)

Thats not the issue here. You got off because the officer failed to correctly identify himself, not because he wasnt in uniform. They are not the same thing, how else do you think plain clothes officers and detectives are able to execute their duties?

Original poster...Good luck with it all ;)

Note to self: underwear on head is bad :laugh:

If they are performing traffic duties, they must be in the correct attire to do so

back to the Question.

Unfortunately there are too many variables to answer this question with any certainty.

Variable 1 - Vic Police can inspect a vehicle and if in the officers opinion he/she thinks it is unroadworthy can issue a defect notice. Most officers would not know what was legal or not, so they tend to defect a car to make sure it is checked and legal

Variable 2 - Officers length of service. A serving member of the Victoria Police who has recently graduated and in in his/her probation period prior to confirmation ( ie first 12 months out of the academy before becoming a real cop) is required to have a certain amount of stat's to show they have been an active member of the force. Stats are logged by shift, by post and these can include traffic offences or briefs ( where they send someone to court for a more serious offence). Get someone out of the academy with a point to prove and you could be fined.

Variable 3 - The Victoria police standard practice of " the attitude test". Basically a cop will pull you over for something random to see how your attitude is, fail the attitude test and bang, there is your defect and possible fines depending on how badly you fail the attitude test.

These are 3 main things that a senior contact in TMU told me just before I posted this.

However, you do have some rights and responsibilities.

In short it is your responsibility to make sure your car is in a roadworthy condition when driving on public roads, that you obey road laws and drive in a safe manor.

You do have the right has a motorist to ask for the police officers name, badge number, station and supervisor. You also have the right to take the matter to court to appeal your fine/ defect etc and to seek some compensation if it can be prooved that your vehicle was roadworthy at the time of being defected.

You also have the right to complain if you feel you are being constantly harrassed by police and this can be done to the office of police integrity.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I do believe from context he is talking about a S0/S1 R33 RB25 with associated ECU and Wiring for that, and a manual gearbox into a R34 N/A Auto. I don't have the knowledge of all the pinouts and such but my gut feeling from doing my own conversion is to use as much of the R33 stuff that you can. The "car" wiring is quite seperate from the "Engine" wiring when all things are considered. The only things to truly consider 99% of the time is the cluster, reverse lights and potentially disabling the 'not in P/N' immobilizer circuit.
    • A realistic expectattion of how long it has to last also comes down to.... when do you think you will be banned from registering and driving old petrol powered shitters? It's 27 years since that thing was built. It probably rusted out 15 years ago. It was probably repaired and looked OK for another 10. If you do a similarish bodge job now, or perhaps slightly better with some actual rust conversion and glassing, then.... get another 10-15 years out of it, after which you'll only be permitted by the CCP to drive electric cars manufactured in their Shenzen zone anyway. 
    • Let me assume that the concern over a manual ECU is that the NeoDET that you have was an auto and has an auto ECU. That ECU will not be a problem, but you WILL have to Nistune it. And you would have to Nistune it even if you had a manual ECU, because the turbo ECUs will shit the bed if they do not have all the things that they were told they have to have, to be happy. The big one being the TCS CU, which you won't have in your car. Anyway, with an auto ECU (which I have running my originally auto NeoDET in an R32) Nistune allows you to put in a Stagea image which doesn't panic about the absent TCS, and allows you to override a whle bunch of other annoyances that would otherwise see the check engine light on 100% of the time. Also, you can't wind up the power very far on the stock NeoDET ECUs without Nistune, because the boost sensor gets in the way. Nistune allows you to push that problem much further up the dial. Do you even have the boost sensor with the engine? Without it, you are SOL and will need an aftermarket ECU (or to find a sensor somewhere, god knows where). I can't tell you what the wiring loom differences are in a 34. But what Duncan said above needs to be considered. When you say "loom", does that include the transmission loom? Because you will need to swap out the auto tranny loom for the equivalent manual loom, and get rid of the neutral/park start interlock (basically hot wire it).
    • I have had the r3c in for years now, maybe close to 7 years and it has never missed a beat, anyone can drive it. Super easy to drive around town, the hotter it gets does get a little hard but it holds the power easy as 
    • Shit thing to find eh? I guess the big issue is that whatever "fix" you do now, it might slow the rust down but won't fix it. I just wanted to add that in no way is fixing sheet metal in 3 dimensions the place to start with welding....that is a pro only job because its too hard to work out where things should be, let alone doing a clean enough job that it can look OK and still be strong too.  I needed to get a new rear quarter panel on the GTR and it took a pro weeks to get the old one off cleanly, new one on in the right place and looking somewhat like it should have with most of the previous connecting panels in place. Gluing a couple of bits of metal together with a welder in the garage is doable, but that is totally different to doing panel  replacement
×
×
  • Create New...