Jump to content
SAU Community

Sold

kjb_r33

By kjb_r33,
in For Sale (Private Whole cars only)

 Share

Recommended Posts

kjb_r33 Experienced

kjb_r33

Posted
Posted (edited)

Have owned car for 4 years.

Completely stock with the exception of a rb20 wastegate actuator.

Few marks in the interior and could use a paint job, but other than that its a great reliable car.

Within the last 2 years its had a new water pump and timing belt fitted.

Only reason im selling this is because i also have a r32 and a 300zx, its just not getting driven enough and its a shame to see it sitting there.

The following pics are a few years old now, will get some current ones tomorrow. Same car, just has a bit of paint fade and stone chips at the front.

post-536-1166825010.jpg

post-536-1166825026.jpg

post-536-1166825043.jpg

Looking for 6500. So low mainly due to the fact that it does need a paint job.

EDIT: Forgot to add, its got 140,000 k's on it

Edited by kjb_r33
Link to comment
https://www.sau.com.au/forums/topic/148451-sold/
Share on other sites
  • 2 weeks later...
  • 3 weeks later...
  • 1 month later...
  • 1 month later...
  • 4 weeks later...
  • 2 weeks later...
  • 2 weeks later...
webber Proficient

webber

Posted
Posted

Sold to me,

Thanks Ken,

Going in for a minor Straight and Paint this week, i will send you photo's when it is done.

Drove it home well over 700KM's did not miss a single beat

P.S. the other item is in a post pack waiting for the post office to open tuesday.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/148451-sold/#findComment-3170986
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
    • MBS206
      R32 update from 1990's spec.

      By MBS206 · Posted

      With ordering the belt, you're doing water pump and the idler and tensioner at the same time too yes?
    • joshuaho96
      RB26DETT Sketchy boost mod?

      By joshuaho96 · Posted

      This is just a dumb way of keeping the wastegate closed to make more boost. Undo it and either follow the factory setup or redo it properly. Manual boost controllers just use a spring preload to determine when to close in response to boost pressure so it no longer vents to atmosphere.
    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
×
×
  • Create New...