Jump to content
SAU Community

Recommended Posts

hey guys i thought it's time to sell my beast and move on to other things , its a R32 GTS4 with fully built RB26 the engine was installed in japan but it got built here

MOTOR : CP pistons

cryo rods

cryo crank

full port and polished head

N1 oil pump

brand new water pump

camtic head gasket

power FC with hand control

all gates hoses and belts

600x100 trust fmic

polished plenum and all piping

3 inch trust stainless exaust from turbo

bosch 044 fuel pump

nismo rebuilt 5 puck 600 hp clutch

TURBO : garrett GT3540

twin R33 airflow meters

stainless polished pipes off front of turbo

tial 44mm wastegate

all braided lines

SUSPENSION: tein coilovers all round

cusco rear diff

BODY :fine silver paint on the bottom

custom made candy gold on top with black pin strip

HOK pearl ice through the whole car

du-luck front bar with nismo race side skirts

and a big rear bar from japan

shaved boot key hole

twin vent carbon fibre bonnet

tinted windows

paint job is about 2 months old

INTERIOR : GTR seats

4 HKS guages

jvc touch screen head unit

new leather boots for gear knob and hand break

the engine has about 5000k's on it and it is in perfect condition it has never been down the

strip as it was planned to at jamboree i am the first owner in australia , the car was tuned

at godzilla motorsports by mark jacobson the car made 507 hp on 21 psi at the wheels ,

there could of been more boost so the car should easly make the 530 hp 400kw . its an

animal on the street so the buyer will be very happy, on the street the car only runs off the

wastegate which is 13 psi , the car will not be sold with a boostcontroller never got around

to getting a new one sorry . the car should be running a high 10 low 11 in 4wd im located in

brisbane south side 0422883933 matt will sell anywhere in aus , prefer brisbane . no joy rides

thanks . if i think of anything else i will post cheers . $25,500 ono if any one thinks thats a bit dear let me know and why cheers

post-9273-1167120489.jpg

post-9273-1167120544.jpg

post-9273-1167120597.jpg

post-9273-1167120657.jpg

post-9273-1167120760.jpg

Edited by drewecrome
Link to comment
https://www.sau.com.au/forums/topic/148748-500hp-32-gts4-rb26/
Share on other sites

thanks heaps fellas yeah been doin it up for about 2 years now the head is fairly stock port and polished head new vavles pretty much every thing new and ARP head stud kit , if it didnt make 500 at the wheels then i would of done some head work but it did it pretty easy and safe so yeah . thanks

Edited by drewecrome

Hey Just a few questions

*What year is the car?

*Why was the motor built here but then sent to Japan for install?

*Could you post some interior pics?

*Why are you selling?

*Do you have any standard body parts? (for trucking, wouldnt want that kit getting fu**ed)

*At what RPM does the turbo begin to spool and what RPM does it hit full boost?

*Do the Feds hassle you much?

*When you dyno'd at 507HP at 21PSI, was that in 2WD or 4WD

*Do you have a 4WD/RWD switch installed?

*Are the brakes stock?

*What power are you making off wastegate PSI? (13PSI, and is that what you run for daily driving?)

Cheers

Hey man,

interested in a trade for a S14a, It is the X fiber motive show car. Harlequin paint, leather & Suede everywhere, buckets etc.

If you are interested please let me know trough a PM

Thanks, jake

Here a link to check car out if you prefer

http://www.nissansilvia.com/forums/index.p...=0#entry2822364

Edited by jakegts

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...