Jump to content
SAU Community

Recommended Posts

Originally posted by sidewaymambo

I need a set of stock brake pads (F & R) even if they are half used...

Cheers,

Phillip

Phillip,

I've got a front set of stock pads with *Jay run's into the other room* about 6-7mm of meat left on them....

Actually, looking at these, I'm not sure if they are stock !! Do the stock pad's have a green metal backing !!!

J

Ummmm, how can I explain this.... The stock pads felt like standard pads, while the EBC's have more intial bite to them.

Bad explaination, sorry :P

One of the reasons I got rid of the stock pads was cause they can be noisey. Sometimes they would squeal when pulling up at the lights. But the front disks were pretty glazed over too, so matbe that had something to do with it???

J

Originally posted by DJ_L3ThAL

if jay's arent stock ill have the stock fronts i can sell to you by the end of this week ( getting some ebc greenies then) so make me an offer :D

DJ - you'll like the greenstuffs :P Just make sure you get the disc's machined too. I got about 20% better braking from them...

yer the place im geting them done say i might not need machining, they'ree inspect when i come in or the brakes and if the discs need it they'll do it but they say sometimes they are still good for new pads (i doubt they'd wanna be dodgy as i'd be back quick smart if i ass-end saomeone coz the brakes they fitted failed to pull me up properly)

all places machine the discs to be safe when they replace the pads.. but they don't necessarily need to do.. then they pull you up on "minimum thickness" requiring new discs costing a lot - i think its the greatest scam in the automotive industry.

Yeah, that's true. I remember dropping my old car off for a tune and getting a phone call an hour later saying that all the pads need replacing and the discs need machining. I told him that I checked them a week prior and that he was trying to rip me off !!!

He's responce - oh, we'll check again, they might be OK then !!!

Anyway, Sidewaymambo - I've attached a pic of the pads I've got. Don't worry, I've got 4 pads, only took a photo of 2 of them :P

Originally posted by DJ_L3ThAL

if jay's arent stock ill have the stock fronts i can sell to you by the end of this week ( getting some ebc greenies then) so make me an offer :)

thanks..DJ..

I will see what jay can find out for me..really thanks..

Originally posted by sidewaymambo

jay..would you able to see any print on them? just want to make sure they are soft enough..thanks..

I might start a quick thread in the maintanace section to see if anyone has seen stock pads before. I'm nude on this, not sure if they are stock or not - I presume they are though.

There isn't any brand name stamped on them (if the were apexi ones etc, I'm sure it'd have their name stamped all over them - damn rice) :)

The numbers that are stamped on them are 6GXu 236M.

I'll see what I can find out.

J

I haven't had any luck yet with trying to confirm that they are factory pads :P

I've done a search around to see if I can find some pics on the net of stock pads, but again, no luck :D

Not sure what you want to do ???

Cheers

Jayson

mine are definitely stock pads (my car was 100% stock when it came in, ecu wasnt even touched so i doubt the pads were lol) so umm yer im taking my car in tomorrow to get brakes done so ill have them from tomorrow onwards (this is only the front ones)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...