Jump to content
SAU Community

pRoBleM

croat

By croat,
in General Automotive Discussion

 Share

Recommended Posts

croat Mentor

croat

Posted
Posted

I have this problem when i rev my car and its not in gear the revs come back down and fall below the normal idle level. The car pretty much stalls then pics itself up again and idles normally. same thing if i take of fast then put the clutch in. anyone had this problem? Or know what is wrong?

Thanks...

Link to comment
https://www.sau.com.au/forums/topic/14981-problem/
Share on other sites
Al Grand Master

Al

Posted
Posted

Read about this in HPI mag, problem is worse if you have a bigger turbo, should not really happen if engine is stock.

As you accelerate or rev, the butterfly in throttle body is open, once you let go of the accelerator the butterfly shuts. Due to the suction of air under acceleration, some of the air bounces off the butterfly and goes back through your a/f meter. This cools the wires in the a/f meter tricking the computer into thinking the engine requires more fuel, thus floods the motor for a split sec. HKS have a device to overcome this problem, not sure of the name.

Before doing anything, make sure the a/f meter is clean.

Link to comment
https://www.sau.com.au/forums/topic/14981-problem/#findComment-304205
Share on other sites
Al Grand Master

Al

Posted
Posted

The ecu is programmed for a plump-back, this floods the motor for a split second, to compensate for the lack of air.

Best bet is to put the stock BOV on and test it. Could solve all your problems, and make your car more enjoyable to drive and legal.

Link to comment
https://www.sau.com.au/forums/topic/14981-problem/#findComment-304232
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Yes I can see how that would put you off HFM, especially with the price of good quality brake fluid. From what I understand it as you say the BM50 is the standard BMC for a R32 GTR, I must admit I would like to go far a Genuine Nissan BM57, but lack of cash prevents that at present. With the price being so close between the genuine BM50 and BM57 a BM57 New it seems a better choice as you gain that 1/16 bore size with the BM57, I would be interested in how much difference you feel with the BM57 fitted. I am going to take SteveL's advice in the short term and see how much actually comes out of that proportioning valve vent and save up for the Genuine Nissan part. Thanks for clarifying the HFM failure
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      Thanks mate. I just got the post inspection 1/2 done from state roads when the starter motor packed up, either that or the car alarm system is having trouble.  OEM part number 23300-AA112.
    • oHBoy.
      Starter motor replacment teeth count.

      By oHBoy. · Posted

      Hi, I though I was coming to an end in finding a replacement starter motor for a rb25de neo. I came across a starter motor from Taarks and a message below stating: Direct fit. 11 Tooth count. All below part numbers have been superseded to 11 teeth. Can some body shed some light on going from 8 teeth to 11 teeth apart from 36-month / 25,000 km warranty for passenger vehicles to 12 Month Warranty. Compatible with the following Nissan part numbers: 23300-20P00 23300-20P01 23300-20P05 23300-20P10 23300-20P11 23300-AA111 23300-AA112 23300-AA300 23300-08U10 23300-08U11 23300-08U15  
    • niZmO_Man
      J50 clock date suddenly reset to January 1

      By niZmO_Man · Posted

      Low battery? Maybe check capacity? I know first-hand, on BMWs if your battery drops below 80% capacity, it starts causing strange issues.
    • niZmO_Man
      Wheel Sizes & Offsets For Skylines

      By niZmO_Man · Posted

      8.5 +37 = should fit rear, but I think it'll hit on front. What you want is low 30s/high 20's front, mid 30's rear. That 17" screenshot you posted looks good, I'd run it on my R32 (but that's long dead now). For tyre sizes, my rule of thumb is: 8': 235, 9": 255. But that's just my opinion. Nismo sizes: 18x8.5+35/18x9.5+38 is a good starting point.
×
×
  • Create New...