Jump to content
SAU Community

Recommended Posts

look i got a s13 sr20de silvia i want to get rid off it had a front END when i purchase this car

which i have replace it with a new radiator support. there is no rail damage wat so ever

the car is in parts(the engine needs to be put back in) i have all the parts that is required to put

this car back on the road. its just im gettin lazy now.

THE PRICE I WANT IS $2500 firm

located western sydney

or call 0415816667 for richard

post-30786-1168073740.jpg

post-30786-1168073802.jpg

Edited by Tim N
Link to comment
https://www.sau.com.au/forums/topic/150270-eois13-sr20de-silvia-2500/
Share on other sites

do you have more pictures?

im from melbourne so how would i be able to get my hands on it

do you have the stock front bumper or anything like that?

what parts are missing.

would you be able to place the engine back in? if you could would be great.

how about wheels? is it also drivable ? how about rego and complance and all that other stuff?

lol didnt really answer my question?

do you have more pictures?

would you be able to place the engine back in? if you could would be great.

how about wheels? is it also drivable ? how about rego and complance and all that other stuff?

do you have the stock front bumper or anything like that?

PLEASE ANSWER.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...