Jump to content
SAU Community

Recommended Posts

hey, i have a nissan r33gtst and i have just recently put new light bulbs in as the old ones failed. but now when the lights are on im experiencing a rough idle and eventually my car will stall!!!

anyone else experience this or know why it is happening?? my appreciation for help in advance. :P

cheers james

Link to comment
https://www.sau.com.au/forums/topic/151424-turn-on-lights-loss-of-power/
Share on other sites

Sounds like a short in the electrical system in your car.. that could have caused the globes to burn out in the first place... have you installed any electronic devices recently? or check all the wiring for any aftermarket devices such as turbo timer, CD player, Amp .etc.

Get an auto electrician to check it out

Cheers

Edited by QRI05E

Check all the engine earths and also the earth on the headlights, make sure there is no corrosion build up around these areas.

Did both headlights blow at the same time? or did only one go and then you decided to replace both?

Alternator could also be on its last legs, you need to see what the current jump is on the battery with a multimeter when you start the car to know if its dieing. You can check the alternator directly too but you still need to grab a multimeter. Check the earths first, also put the inerior light on and the A/C and see if it will die by using other items.

Edited by James_03

i find i have the same problem at night time, when im driving car feels like i take my foot off the gas then comes back in also have the bad idle at night while lights are on.. im gonna buy a volt stabalizer thingo n see how that goes, even if it doesnt help alot it wouldnt hurt to have one i guess

when i install this im also puttin new battery in

Edited by 2gceffy

It sounds like your alternator. Best way to check it is to start your car and then disconnect one of the terminals from your battery. If the car turns off its your alternator but if it doesn't then its something else.

disconnecting the battery while engine is running is a risk to damage the alternator`s governor.

to check alternator just measure voltage @battery terminals, normal value is 12.3-12.8v with engine off and ~ 13.2-14.5v with engine on and healthy alternator.

hey i have checked my voltage and it all seems to be fine about 14.4-14.3 with car started and everything going flat out, lights and aircond. while i was looking over everythig i noticed that there was a steel rope kinda thing only small tht looks like it was connected to my catalytic, but no longer is. i reconnected it and ill see how that goes. anyone know what that is???

ps.. im not that crash hot with car electrics... :(

temperature sensor for the cat. if the cat gets too hot a dash light shows up to let you know.

shouldn't normally happen unless there's something wrong or you're driving it like it's stolen, but might as well have it plugged in since it's there!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...