Jump to content
SAU Community

Recommended Posts

hey, i have a nissan r33gtst and i have just recently put new light bulbs in as the old ones failed. but now when the lights are on im experiencing a rough idle and eventually my car will stall!!!

anyone else experience this or know why it is happening?? my appreciation for help in advance. :P

cheers james

Link to comment
https://www.sau.com.au/forums/topic/151424-turn-on-lights-loss-of-power/
Share on other sites

Sounds like a short in the electrical system in your car.. that could have caused the globes to burn out in the first place... have you installed any electronic devices recently? or check all the wiring for any aftermarket devices such as turbo timer, CD player, Amp .etc.

Get an auto electrician to check it out

Cheers

Edited by QRI05E

Check all the engine earths and also the earth on the headlights, make sure there is no corrosion build up around these areas.

Did both headlights blow at the same time? or did only one go and then you decided to replace both?

Alternator could also be on its last legs, you need to see what the current jump is on the battery with a multimeter when you start the car to know if its dieing. You can check the alternator directly too but you still need to grab a multimeter. Check the earths first, also put the inerior light on and the A/C and see if it will die by using other items.

Edited by James_03

i find i have the same problem at night time, when im driving car feels like i take my foot off the gas then comes back in also have the bad idle at night while lights are on.. im gonna buy a volt stabalizer thingo n see how that goes, even if it doesnt help alot it wouldnt hurt to have one i guess

when i install this im also puttin new battery in

Edited by 2gceffy

It sounds like your alternator. Best way to check it is to start your car and then disconnect one of the terminals from your battery. If the car turns off its your alternator but if it doesn't then its something else.

disconnecting the battery while engine is running is a risk to damage the alternator`s governor.

to check alternator just measure voltage @battery terminals, normal value is 12.3-12.8v with engine off and ~ 13.2-14.5v with engine on and healthy alternator.

hey i have checked my voltage and it all seems to be fine about 14.4-14.3 with car started and everything going flat out, lights and aircond. while i was looking over everythig i noticed that there was a steel rope kinda thing only small tht looks like it was connected to my catalytic, but no longer is. i reconnected it and ill see how that goes. anyone know what that is???

ps.. im not that crash hot with car electrics... :(

temperature sensor for the cat. if the cat gets too hot a dash light shows up to let you know.

shouldn't normally happen unless there's something wrong or you're driving it like it's stolen, but might as well have it plugged in since it's there!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...