Jump to content
SAU Community

Recommended Posts

Hi guys,

Just a quick question, noticed that after driving my car, if i pop the bonnet there is always a gurgling sound comming from the engine, sorta sounds like boiling water, not quite that loud, just a slight gurgle.

Is this normal, is there anything i should be concerned about? Car is an r32 GTR.

Cheers,

Dave.

Link to comment
https://www.sau.com.au/forums/topic/152922-gurgling-sound/
Share on other sites

i had a gurgling sound from behind the dash in my old supra and turned out to be the early stages of a blown head gasket...

exhaust gasses were slipping through the head gasket and into the water system causing the gurgling sound

if i were you i'd get it checked out by a radiator shop...

Link to comment
https://www.sau.com.au/forums/topic/152922-gurgling-sound/#findComment-2846165
Share on other sites

I have also experienced this in a camry for about 2 months before my head gasket completly blew. You can check if there is any gasses going into the coolant by running the engine without the radiator cap on and checking to see if any gasses are bubbling out through the coolant. Either that or get your coolant system pressure tested. hope this helps.

Link to comment
https://www.sau.com.au/forums/topic/152922-gurgling-sound/#findComment-2846704
Share on other sites

could just be a simple heating issue... when you turn your car off.. the highest point of collant pressure is then. You might have a slight slpit hose.. or you havent got a completey bled free cooling system.. I would suggest its just the coolant water bubbling away.

Link to comment
https://www.sau.com.au/forums/topic/152922-gurgling-sound/#findComment-2866111
Share on other sites

have a mechanic gas test the radiator, i think it checks for CO-2, but detects exhaust gas in the cooling system.

i had this issue before, and had the test done, it should slightly positive for the gas, so a few months later i changed the head gasket and was all sweet. even though it wasnt over heating.

Link to comment
https://www.sau.com.au/forums/topic/152922-gurgling-sound/#findComment-2871824
Share on other sites

problem is - bubbles popping inside your coolant are basically small explosions = corrosion. Get it checked before it eats away at something. Even if it is something as simple as a unbled coolant system, get it fixed asap

Link to comment
https://www.sau.com.au/forums/topic/152922-gurgling-sound/#findComment-2872455
Share on other sites

I had the same problem in my runabout car. (celica 89) changed my radiator cap and hasn't done it since.

You know the old saying (K.I.S.S.) Keep It Simple Stupid.

You don't want to jump the gun and spend heaps of cash and it ends up being something simple.

hope I helped.

Link to comment
https://www.sau.com.au/forums/topic/152922-gurgling-sound/#findComment-2872474
Share on other sites

mine started making a gurgling noise after i put a new turbo on...

the gurgling noise seems to come from the turbo area.. it happens for a while after the car is turned off. does that sound bad... ?

i dont have any leaking/overheating issues.. everything seems pretty good though.

how do u bleed the coolant.. just undo the cap and let it run for a little while or something ?? oh yeah i use castrol radicool i think it is.. and my radiator cap has one of them buttons in the middle you can press.. if thats good or bad ??

thanks :P

Link to comment
https://www.sau.com.au/forums/topic/152922-gurgling-sound/#findComment-2872655
Share on other sites

mine started making a gurgling noise after i put a new turbo on...

the gurgling noise seems to come from the turbo area.. it happens for a while after the car is turned off. does that sound bad... ?

i dont have any leaking/overheating issues.. everything seems pretty good though.

how do u bleed the coolant.. just undo the cap and let it run for a little while or something ?? oh yeah i use castrol radicool i think it is.. and my radiator cap has one of them buttons in the middle you can press.. if thats good or bad ??

thanks :P

bleed tap on the front of the plenum above your fuel pressure regulator, loosen it off it once its hot since this should be the highest point of the cooling system, once bubbles stop close and it will be bled.

as for turbo, if its high mount it may be acting as the highest point in the system, if there is air in that area once you switch off the car, then this will allow the water to boil in that area.

Link to comment
https://www.sau.com.au/forums/topic/152922-gurgling-sound/#findComment-2872725
Share on other sites

the turbo is a 2535.. is that a high or low mount ??

ill try bleeding her again also, cause i didnt no about the bleed tap thingy :P

bleed tap on the front of the plenum above your fuel pressure regulator, loosen it off it once its hot since this should be the highest point of the cooling system, once bubbles stop close and it will be bled.

as for turbo, if its high mount it may be acting as the highest point in the system, if there is air in that area once you switch off the car, then this will allow the water to boil in that area.

Link to comment
https://www.sau.com.au/forums/topic/152922-gurgling-sound/#findComment-2872792
Share on other sites

My car seems to make a couple gurgling sounds as well, only it isnt while running or after a drive, it is once every morning because of how cold it is starting. it usually takes 2-3 times for the engine to actually start as well. then all day it is perfect. same thing?

Link to comment
https://www.sau.com.au/forums/topic/152922-gurgling-sound/#findComment-2875357
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...