Jump to content
SAU Community

Recommended Posts

Hey guys,

Have had trouble starting my car only sometimes lately. Today it took me about 10 turns of the switch to get the starter motor to turn over the engne.

I get in the car, put the key in, turn it past accessories to the 'ON' position I guess, let the fuel pump go for about 5 seconds before turning the key to 'START' and nothing.... just cuts out the radio. Tried it about 7 times, then took the key out, turned it around, did the same thing, did the same thing first attempt, and then on 2nd attempt fired straight away.

Has this happened to anyone else? And what could be the causes?

Worn out ingition barrel not contacting anymore (I have no idea how it works inside the barrel)?

Starter motor contacts bad??

It used to only do it maybe once or twice at most, and only usually every 5 or so times of starting the car (it would usually strart straight away), but yesterday afternoon and today afternoon I had trouble.

Any other ideas?

Thanks,

Fixxxer

Link to comment
https://www.sau.com.au/forums/topic/153238-starting-problems/
Share on other sites

If the key goes in and turns to start normally the first time before flipping it then its got nothing to do with the key or barrel. However commodores use an anti theft device in the key head that flipping the key sometimes helps, but thank god you dont have a commonwhore!

Most likely a starter problem. To be safe you should get a multi meter and load test the battery. First unplug the ignitor so the car wont start. Attached the two terminals of the multimeter to the battery terminals then get someone to try cranking the engine and while its winding over watch the reading on the multimeter. If it drops below 10 volts then your battery is dieing. If not and it stays around 11-12 volts the battery should be fine and you can be more sure its the starter/solinoid causing the fault.

Battery should be fine, its a good battery, I replaced it only about 3 months ago....

It's not like the starter is struggling to start the car, it's like the power is not getting to the starter, and then suddenly i turn the key the right way or something and it fires instantly.

Fixxxer

OK then we can rule out the battery, good. Next look at the starter & solinoid (which are combined) and earthing of the circuit. If there isnt a good earth (strap) you may aswell be not supplying enough power as its the same end result.

Deren

I had the very same problem on my car some time ago!

It ended up beeing the front + and -poles on the left side of the engine bay.

The thing was that the prior owner had connected front-lights to the +pole and that created a gap big enough for dirt getting in and ruin the connection.

Apperently the connection was good enough for panellights and such, but not good enough for the starter.

If i recall correctly i think the windows wouldnt move either...

Hope that helps!

As the brushes wear in a starter you will get an inconsistent starting patterns. But I have also seen a brand new battery off the shelf that I have had to fit to a customers car and it has had a brake in between the cells.

Do what Deren said by checking battery voltage, whilst cranking - this will give you the best indication, also check you main battery lead going to the starter - if these look ok - its time to pull the starter out, and give it to some mug they call an auto electrician :P.

Cheers

Sumo

Ok I will look around the starter motor and see if there is anything wrong with connections.

Next I'll check the battery and connections to the battery, but like I said this doesn't seem to be a problem as there is plenty of kick to start the car when the starter works, and this has been a problem ever since I got the car a year and a half ago (with a different battery).

Fixxxer

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey guys! Y'all are the masters so figured I'd check in on a few items here. - My engine sounds ever-so-slightly more raspy than the other NA RB25s I've listened to. It's barely noticeable but definitely a slightly different sound. - When I back off the throttle at high RPM, I will sometimes get a pop out of the exhaust, assuming this can be diagnosed as misfire. Some history on the car: - Had an exhaust leak in auction sheet but was claimed to be fixed by seller (bought from USA importer).  - Car's coil packs and sparks were replaced when it was sold to me, but unsure on what the gap is and whether the coil packs are correct.  - A prior mechanic had misdiagnosed a pilot or throwout bearing sound as LSPI/detonation. Had played with timing a bit, pops/raspy sound of engine just got worse. Got timing reset. - Had failed emissions a few times. First time went in as is, failed. Second time, replaced cat, still failed, running rich as hell. Third time replaced o2 sensor, passed. Car still smells gassy though. - Timing belt and valve cover gasket also replaced.  - Gas mileage is... low. about 350-400K per tank.  Any idea if I'm having any serious issues here or does this all sound like normal old NA RB stuff and I'm fine to drive it with the pops/slightly raspy engine? If it'll help, I can get drop a video of the sound of the engine.
    • So....to find any R chassis part number, get your VIN (will be something like ER33-xxxxxx for you) and go to: https://www.amayama.com/en/genuine-catalogs/nissan and enter it. From there you have access to a web version of Nissan's part system, FAST. It is a bit tricky to get used to, so maybe have a shot and post up what you think.  You can also search by general model but note in some cases your car might have different options so VIN is safest.  On diagram 211 I got 14075-75T16 for Connector, Water Hose If I search for part 14053‑21U10 that you posted, that is also a water hose but not the one bolted to the plenum and 14075‑04U00 is the fitting where the water hose goes into the block.
    • Yeah now we are talking I much prefer coolers in the front middle because it lessens the chance of a small bump to a corner stopping the whole event. I was thinking the AT cooler can move out of the radiator, delete the AT/engine coolant interwarmer and mount a separate cooler with a thermoswitch somewhere further back as is common in racing, that would be one thing. Beyond that, the engine oil cooler is an obvious one to move to the wheel arch, potentially one on each side, but unused space is an issue. I did have a earlier pic with the bumper off but it doesn't show how busy the corners are: DS is full of the auto driving sensors and PS is totally fully of windscreen washer fluid reservoir But ultimately I was hoping to keep the AC, and the water/air heat exchanger is fundamental so it is not just the radiator that needs to be in front BTW here's airflow to the rad as it ran at the track (one horn is gone now and I'll remove the lights next time):
    • your right the maps for Australia came out in 2017 but are 2010 maps. i got the updated maps SD card put it in and it was the same. Same maps in my Brothers Nissan Patrol. 2020 i think his car is
×
×
  • Create New...