Jump to content
SAU Community

Recommended Posts

Hay guys..

Im wanting to convert my RB20DET to an RB20DE.

As far as I know..

I need:

Headers

New head (?? Can an Rb25DE head fit without hassle?)

ECU (piggy back or new chip?)

pluming for the new intake

Exhaust flange (???)

Anything I missed?

Thanks in advance guys!

Link to comment
https://www.sau.com.au/forums/topic/153697-converting-turbo-to-na/
Share on other sites

Why do you want to N/A a turbo engine....?

Just thought i would ask...

i was holding back on that question also....

people waste money to go forwards not backwards,

it would be a better idea to sell the car and buy a non turbo one?

instead of being down on money you will have money left over or you could even upgrade to a 33 non turbo

Because I dont know what kind of deadshit drove the cars..

At least with this.. I know everything thats happened to it.. I know how well it runs.. I know that everything is in perfect working order and of a high quality.

I would be wasting more time/money in fixong other peoples problems.

Where as with this.. I can spend 1K save more money.. and easly swap it back to turbo further down the track.

well pretty much all you will need im guessing would be, na ecu, na intake pipe, na exhuast headers, and possibly na injectors oh and to fiddle with the timing. otherwise should be pretty easy.

just find out what people need for converting an na to turbo, and reverse it

Your logic makes no sense, however, if you must:

Swap the entire engine over. You can pick up a decent RB25DE for under $1k which will bolt straight up to your existing box & flywheel.

Saves mucking around

I aggree with the above but it doesnt suit your " know everything thats happened to it.. I know how well it runs.. I know that everything is in perfect working order and of a high quality." argument.

Essentially all you need is to remove all the turbo gear, and run some stock headers (or some extractors)

But i would probably take it a bit further than that and revert to N/A Injectors and ECU, also up the compression to something similar to stock whether it be by some shaving/decking and/or NA different pistons - better for fuel economy. Cam etc is the same...

But if i was you.. i would be selling it and buying a second hand RB25, something a little more drivable as an N/A and just as good economy

As stated above it wont be any cheaper. It will drive worse than an NA model due to lower compression. Bite the bullet sell it and buy an NA car. U can get tests done to see if you are buying a healthy car or not. Not everyone thrashes the living daylights out of our cars.

Cheers

Chris

something different :)

u'd be the first to do it

as suggested, sell it and buy a n/a, u'd have money your way, rather than spending it

cant u just get 3rd party insurance

Edited by andz69
  • 3 months later...

how much did it end up costing?

not being rude but u would have made money selling the turbo and buying the n/a....not sure that i would spend money when i could make money....also the car is still in the turbo model so it should still have attracted the higher insurance....what did u end up having to do?

Well.. To all you nay sayers..

Its been completed..

4 Door R32 GTS4 with RB25DE.. and it runs as sweet as.

In your original post you said it was an RB20DET going to RB20DE. My engine knowledge isn't encyclopedic, but the last time I checked pulling the turbocharger off an engine didn't give it another half a litre of displacement.

So you basically did what everyone else told you to do, and got an engine conversion.

I fail to see where you're getting "naysayers" from, since the objections people raised to your idea were for a situation you decided not to go through with.

  • 4 weeks later...

You know what you need bro? A spinning,snapping, turning, twirling flykick to the head... LOL... nah, seriously bro - why the heck would you want to downgrade... ???????? Man... you're nuts.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...