Jump to content
SAU Community

Recommended Posts

Hi all,

A while back I stumbled across a thread where people had bought front tie rod ends from Pedders for thirty-odd bucks. I am just chasing some part numbers as the stores I have called (in Adelaide) don't reckon such a product exists.

It was also stated that the R32 tie rod ends come in 2 sizes from Pedders. I assume GT-R and maybe GTS-4 must be different from GTS-t and GTS.

I have taken some measurements of my tie rod ends as they don't have a part number stamped into them.

Length from threaded end to centre of knuckle - 100mm

Overall length - 120mm

Apologies for the lack of pictures but I don't have a digital camera.

Pedders part numbers preferred, but any part numbers will be extremely helpful

Cheers

Dwayne

Link to comment
https://www.sau.com.au/forums/topic/155345-tie-rod-end-part-numbers-r32-gts-t/
Share on other sites

I used r33 ones. Longer than the r32 but same thread size...never bothered to measure it tho. Just have to count your turns taking the old ones off and making sure to get a wheel alignmnet Straigt Away !

The tie rod ends (or rack ends as u are calling it)

They are "Rackends" since no skylines have "Tie Rods" :-)

tie rod

n.

1. A metal rod that joins and reinforces parts in a structure.

2. Either of two metal rods or arms that transmit motion to the front axle in certain vehicular steering systems.

last time i looked they did, unless i and most japanese parts makers are mislead...

http://www.tein.co.jp/e/products/tierod.html

Edited by Bl4cK32

I have an '93 R33 GTSt and I found Pedders tie rod end length measurements to be a bit out. They initially gave me the PTE926 with 12mm thread but needed the 14mm thread PTE926-14. A great price.

Always get a wheel alignment after replacing steering or suspension parts.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...