Jump to content
SAU Community

Recommended Posts

i have a remapped ecu for sale. it will work in both series 1 and series 2 manual r33s (for those that think the series 2 have the ignitor built into the ecu, they don't). the person i bought it off had it in a series 1, and i had a series 2 motor in my car.

i tested the AFRs at 11psi on standard turbo, fuel system, with just a turbo back exhaust, pod and fmic. at full throttle they from 12.5 from about 3000rpm and slowly drop to 12.0 by about 3700rpm untill about 5500rpm when they start to drop to 11.4 by redline.

the ecu has had rich and retard removed, speed limiter removed and the rev limit raised to 7500rpm. i ran it in my 33 for about 8 months and never had any problems (on 14psi they go a lot harder than on 11psi despite what people say - most of them have never tried it and are only going off what other people have said). i never got to test the afr's at 14psi because the day i had a lend of a wideband o2 sensor the boost controller stuffed up and wouldn't let me go above 11psi. but when i pulled the spark plugs out after 6 months there was no sign of pinging or running lean at 14psi.

i was going to combine this with a safc to get perfect 12.0 afrs but never got around to it and no longer own the car.

asking $200 + $10 postage (or you can pick it up if you want).

located in gympie, qld

contact: marc 0401 217 840, or PM on here.

Edited by mad082
Link to comment
https://www.sau.com.au/forums/topic/155405-r33-remapped-ecu-afrs-tested/
Share on other sites

didn't have it on the dyno. just had a lend of a microtec wideband o2 sensor. at the same boost level it made a slightly noticable difference, but the fact that you can wind the boost up means you can boost up to where you would normally hit r&r and then really have some fun.

hi am i right in assuming i could just replace my ecu (series 1 r33 gtst manual) with this ecu and achieve instant power gains over standard?

a small gain yes. i noticed a little bit of a gain. as for an exact figure i'm not sure as i never put it on the dyno with this ecu.

Edited by mad082
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...